Log:
Assessments - 4, GPA: 5 ( )

Instruções de Operação Global Machinery Company, Modelo LS1375

Fabricante : Global Machinery Company
Arquivo Tamanho: 1.04 mb
Arquivo Nome : d99687b3-627a-458c-98b8-ccb09eef9903.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Only turn laser beam on when tool is on workpiece. 1. Mark the line of the cut on the workpiece. 2. Adjust the depth of cut and bevel angle as required. 3. Rest the front edge of the base on the workpiece. 4. Switch on the laser beam using the laser light on/off button (2). 5. Align the beam with the line on the workpiece. 6. Start the motor by depressing the lock-off button (5) and squeezing the trigger switch (4). 7. Always let the blade reach full speed (approximately 2 seconds) before you begin to cut into the workpiece. 8. Slowly push the saw forward using both hands, keeping the red laser light beam on the line of cut. 9. After completing your cut, release the trigger switch and allow the blade to come to a complete stop. Do not remove the saw from the workpiece while the blade is moving. 10. Switch off the laser beam on completion of the cut. Changing the blade CAUTION. Always ensure that the saw is switched off and unplugged from the power supply before making any adjustments. 1. Remove blade key (23) from storage area (22). Place saw on its side on a flat surface. 2. Rotate the saw blade by hand whilst depressing button (20) until the blade locks. 3. Whilst depressing button (20), turn the blade bolt anti- clockwise using blade key (23). 4. Remove the outer blade flange and the blade bolt. 5. Raise the lower blade guard (14) using lever (13). Remove the saw blade from the inner flange and pull out the blade. Note. Clean the saw blade flanges thoroughly before mounting the new saw blade. Wipe a drop of oil onto the inner and outer flange where they will touch the blade. 6. Mount the new saw blade onto the spindle and against the inner flange. 7. Replace the outer flange and tighten the blade bolt. WARNING. The direction in which the blade rotates has to be the same as the direction of the arrow marked on the housing. Ensure that button (20) is released. Before using the saw again, check that the safety devices are in good working order. IMPORTANT. After replacing the saw blade, make sure that the saw blade runs freely by turning the blade by hand. 8. Plug the machine into a power socket and run the saw under no load to check that it runs smoothly before using it to cut any material. 9. Place blade key (23) back in storage area (22). Maintenance WARNING. Always ensure that the tool is switched off and the plug is removed from the power point before making any adjustments or maintenance procedures. Cleaning 1. Keep the tool’s air vents unclogged and clean at all times. 2. Remove dust and dirt regularly. Cleaning is best done with a rag. 3. Re-lubricate all moving parts at regular intervals. 4. If the body of the saw needs cleaning, wipe it with a soft damp cloth. A mild detergent can be used but nothing like alcohol, petrol or other cleaning agent. 5. Never use caustic agents to clean plastic parts. CAUTION. Do not use cleaning agents to clean the plastic parts of the tool. A mild detergent on a damp cloth is recommended. Water must never come into contact with the tool. General inspection Regularly check that all the fixing screws are tight. They may vibrate loose over time. Power cord maintenance If the supply cord needs replacing, the task must be carried out by the manufacturer, the manufacturer’s agent, or an authorised service centre in order to avoid a safety hazard. Troubleshooting Trouble Problem Suggested remedy Saw will not start Power cord not plugged in Ensure that the cord is connected to the power supply Power fault, fuse or circuit breaker tripped Check the power supply Cord damaged Use authorised service centre to repair or replace Burned out switch Use authorised service centre to repair or replace Faulty motor Use authorised service centre to repair or replace the motor Blade does not reach full speed Extension cord too long or undersized Use extension cord heavy enough to carry the current Tool is overheating Turn off the tool and let it cool down to room temperature. Inspect and clean the ventilation slots Poor cutting Accessory blunted Replace with new circular saw blade Vibration or abnormal noise Loose parts Check to see that all knobs and levers are securely tightened including bevel adjustment knob, depth locking lever and parallel fence locking knob Blade vibrating Ensure that the blade nut is securely tightened Moving parts excessively worn Use authorised service centre to repair or replace Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: GMC Product Type GMC Product CodeA GMC Service Engineer will take your call and, in most cases, will be able to solve your problem over the phone. You are welcome to use this phone-in service to make suggestions or give comments about any GMC product. With continuing product development changes may have occurre...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias