Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Loosen and remove the blade cover locking knobs (10). 3. Remove the blade cover (9). 4. Take the 2 face spanners and use 1 to hold the blade securing nut and the other to hold the flat part of the spindle. Turn the spanner holding the blade securing nut in an anti-clockwise direction to loosen the nut. 5. Remove the nut, outer blade flange and blade. 6. Wipe a drop of oil onto the inner blade flange and the outer blade flange where they contact the blade. 7. Fit the new blade onto the spindle taking care that the inner blade flange sits behind the blade. CAUTION. Always install the blade with the arrow printed on the side of the blade pointing down. The direction of blade rotation is also marked on the blade guard and blade cover. 8. Replace the outer blade flange followed by the blade nut. 9. Use the blade spanner to securely tighten the blade bolt. (Tighten in a clockwise direction). 10. Replace the blade cover and secure it with the blade cover locking knobs. CAUTION. Before using the saw after replacing the blade, check that all the safety devices are fitted correctly including the blade guard and that they are all in good working order. Run the saw without loading it to ensure the blade runs true and there are no extraneous noises. Filling the water compartment 1. The water compartment (8) is incorporated into the main housing 2. The water helps to cool the cutting disc and also limits the amount of dust produced during the cutting process. 3. Fill the water compartment with water. The maximum water level is automatically controlled by the drainage hole on top of the plug, the top of this plug acts as the water fill line. When the water level exceeds the maximum level water will flow out through the hole. 4. Always fill the water compartment to the top of the water fill line to ensure the cutting disc is sufficiently cooled. Operation Making a straight cut 1. Adjust the rip fence (15) to the desired width from the blade using the scale (12) on top of the table for reference. 2. Secure the rip fence to the table by lowering the rip fence locking lever (16). 3. Firmly position the tile against the rip fence and pass through the blade in a smooth action. Note. Do not force the tile into the blade too quickly or with excessive force, allow the blade to do the work. Making a mitre cut 1. Fit the mitre gauge assembly (17) over the rip fence. 2. Choose the desired mitre angle and tighten the mitre gauge locking knob (18). 3. Place the tile into the mitre gauge and hold it firmly in position. 4. Push the mitre gauge together with the tile towards and into the blade. Making a bevel cut 1. Loosen the front and rear bevel locking knobs (5 & 7). 2. Tilt the table to the desired bevel angle using the bevel scales (4 & 6) as a guide. 3. Tighten the front and rear bevel locking knobs before making the cut. 4. Firmly position the tile against the rip fence and pass through the blade in a smooth action. When making a bevel cut the rip fence should be positioned on the right hand side of the blade to better support the tile. Using the REDEYE® laser line generator system Warnings. Do not stare directly at the laser beam. Never aim the beam at any person or an object other than the work piece. Do not deliberately aim the beam at personnel and ensure that it is not directed towards the eye of a person for longer than 0.25s. Always ensure the laser beam is aimed at a sturdy work piece without reflective surfaces, i.e. wood or rough coated surfaces are acceptable. Bright shiny reflective sheet steel or the like is not suitable for laser use as the reflective surface could direct the beam back at the operator. Only turn the laser beam on when the work piece is on the tool. 1. Mark the line of the cut on the work piece. 2. Adjust the angle of mitre and bevel of the cut as required. 3. Hold the work piece in position using the laser line to align the blade with the mark on the work piece. 4. Plug in the machine and start the motor. 5. Switch on the laser beam using the laser light on/off switch (24). 6. Pass the tile through the blade in a smooth action. 7. Switch off the laser beam on completion of the cut. Adjusting the REDEYE® laser line generator The laser line can be adjusted to line up the laser line with the blade. 1. With the power disconnected place a ruler against the flat part of the blade. 2. Turn on the laser line using the laser light on/off switch (24). 3. If the laser line is not parallel with straight edge adjust the laser line in the following way. 4. Loosen the laser light assembly locking knob (22) and move the assembly to the left or right until the laser line is in line with the blade. 5. Tighten the laser light assembly locking knob. Changing the batteries 1. Remove the laser light assembly (21) from the laser light arm (19). 2. Slide off the laser light battery cover (23). 3. Replace both AAA batteries, taking care to insert the new batteries with the correct polarity. WARNINGS. Use only correct batterie...