Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
!CAUTION The motor may stall if improperly used or overloaded. Reduce the pressure (feed rate) or depth of cut to prevent possible damage to the tool if the motor labors. TOOL PARK REST The park swings down to help keep the blade from coming in contact with the work surface when plane is not in use (Fig. 6). The tool park rest was designed to swing up and out of the way by it itself when the back of the plane crosses the leading edge of the workpiece (Fig. 7). FIG. 6 FIG. 7 ADJUSTING DEPTH OF CUT Proper cutting depth should be determined according to the hardness, gumminess or moisture content of the material being cut, as well as the feed rate, and is largely a matter of experience. Start with a light cut and increase the depth setting if the plane moves freely through the workpiece with no excessive load on the motor. Do not change depth of cut while planing. The cutting depth is determined by the difference in height between the adjustable front shoe, and the fixed rear shoe of the planer. As the front shoe is adjusted, it retracts and exposes the blade, which can then remove the desired amount from the workpiece. The cutting depth is graduated from 0 to 5/64 of an inch, and the "0" indicates the blade is fully retracted. Adjusting depth of cut: Rotate depth adjustment knob until the indicator engages the detent which indicates the desired cutting depth on the depth scale (Fig. 1). The planer may be set to cut any depth from 0 to 5/64 of an inch. STANDARD PARALLEL WIDTH GUIDE FENCE The width guide fence can be used to cut various desired widths (Fig. 1). Installing the guide fence: Place the wing knob through the appropriate hole in the guide bracket and screw into the housing. Securely tighten wing knob. -8 Setting the cutting width: Loosen wing knob and slide the fence along the guide bracket to the desired position. Securely tighten wing knob. Be certain that the flat washer (supplied) is fitted between the bottom of the guide fence and wing knob or the guide fence is likely to slip. DELUXE ANGLE FENCE The optional deluxe angle fence (Fig. 8) can be used to cut various desired widths, with the additional capability of guiding the planer on any angle up to 45 degrees, to allow edge chamfering (Fig. 9). knobs and pivot the fence to the desired position. Securely tighten round knobs (Fig. 1). Note that the adjustable front shoe contains a chamfer V-groove, which will follow the corner of a workpiece to allow easier handling when using the deluxe angle/width fence (Fig. 9). 45° FIG. 9 RABBETING DEPTH STOP The optional rabbeting depth stop accessory (Fig. 1) allows the user to set any rabbeting depth from 0 to 5/16 inch. For best results, it is important that the blade be properly 82 mm max 8 mm max FIG. 8 Installing the angle fence: Place the wing knob through the appropriate hole in the guide bracket and screw into the housing. Securely tighten wing knob (Fig. 1). Setting the cutting width: Loosen wing knob and using the width scale, slide the fence along the guide bracket to the desired position. Securely tighten wing knob (Fig. 1). Setting the cutting angle: Loosen round DRIVE BELT The drive belt is a normal maintenance part and should be inspected periodically for wear. If the drive belt shows signs of drying out, cracking or tearing, it should be replaced. If the drive belt will not track properly or comes off the pulleys, it should be replaced. Installing new drive belt: Loosen screw and remove the drive belt cover. Cut and remove the worn drive belt. Before installing the new drive belt, clean both pulleys thoroughly. First place the new drive belt onto the drive pulley then rotate clockwise while pushing the belt onto the driven pulley. Reinstall the drive belt cover and securely tighten screw (Fig. 10). aligned (See "BLADE ALIGNMENT"). The width of the rabbet is controlled by the width fence. The maximum cutting width is 3-1/4", and the final depth is achieved by repetitive cutting until the rabbeting depth guide contacts the workpiece. The maximum rabbeting depth is 5/16" Setting the rabbet depth: Loosen wing knob and using the depth scale on the rabbeting depth stop, set the desired rabbet depth. Securely tighten wing knob. FIG. 10 DRIVE PULLEY DRIVEN PULLEY DRIVE BELT DRIVE BELT COVER -9 Maintenance Service Preventive maintenance performed by unauthorized !WARNING personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station. TOOL LUBRICATION Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change. CARBON BRUSHES The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine ...