Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Earthing terminal Grounding terminal Warning symbol Alerts user to warning messages Ni-Cad RBRC seal Designates Ni-Cad battery recycling program A0 A0 A0 A0 A A A This symbol designates This symbol designates that this tool is listed to that this tool is listed by Canadian Standards by Underwriters Laboratories. Underwriters Laboratories. This symbol designates that This symbol designates this tool is listed by that this tool is listed by Underwriters Laboratories, the Canadian Standards and listed to Canadian Association. Standards by Underwriters Laboratories. This symbol designates that this tool complies to NOM Mexican Standards. -6 BM 1619X00905 3-05 3/24/05 11:00 PM Page 7 Functional Description and Specifications !WARNING Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Circular Saw LOWER GUARD LIFT LEVER TRIGGER SWITCH LOWER GUARD FOOT BEVEL ADJUSTMENT LEVER QUADRANT BLADE WRENCH & STORAGE AREA AUXILIARY HANDLE FIG. 1 UPPER GUARD RETRACTING HANDLE Maximum Capacities Model 1656 Blade 8-1/4" Blade arbor hole Round Depth of cut at 90° 2-15/16" Depth of cut at 60° 1-5/8" Depth of cut at 50° 1-3/4" Depth of cut at 45° 2-1/4" NOTE: For tool specifications refer to the nameplate on your tool. -7 BM 1619X00905 3-05 3/24/05 11:00 PM Page 8 Assembly ATTACHING THE BLADE Disconnect the plug from the power source before !WARNING making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. 1. Press the lock button and turn wrench until lock button engages. Saw shaft is now locked. Continue to depress button, turn wrench counter-clockwise and remove BLADE STUD and OUTER WASHER (Fig. 2). 2. Retract the lower guard all the way up into the upper guard. While retracting the lower guard, check operation and condition of the LOWER GUARD SPRING. 3. Make sure the saw teeth and arrow on the blade point in the same direction as the arrow on the lower guard. 4. Slide blade through slot in the foot and mount it against the INNER WASHER on the shaft. Be sure the large diameter of the INNER and OUTER washers lay flush against the blade. 5. Reinstall OUTER WASHER. First tighten BLADE STUD finger tight, then TIGHTEN BLADE STUD 1/8 TURN (45°) WITH THE WRENCH PROVIDED. Do not use wrenches with longer handles, since it may lead to over tightening of the blade stud. VARI-TORQUE CLUTCH This clutching action is provided by the friction of the OUTER WASHER against the BLADE and permits the blade shaft to turn when the blade encounters excessive resistance. When the BLADE STUD is properly tightened (as described in No. 5 of Attaching The Blade), the blade will slip when it encounters excessive resistance, thus reducing saw’s tendency to KICKBACK. One setting may not be sufficient for cutting all materials. If excessive blade slippage occurs, tighten the blade stud a fraction of a turn more (less than 1/8 turn). OVERTIGHTENING THE BLADE STUD NULLIFIES THE EFFECTIVENESS OF THE CLUTCH. BLADE WRENCH & STORAGE AREA LOWER GUARD SPRING UPPER GUARD LOWER GUARD LIFT LEVER OUTER WASHER Large Diameter Faces Blade RETRACTING HANDLE AUXILIARY HANDLE FIG. 2 Tighten LOWER GUARD LOCK BUTTON Loosen INNER WASHER Large Diameter BLADE Faces Blade STUD BACKVIEW -8 BM 1619X00905 3-05 3/24/05 11:00 PM Page 9 Operating Instructions DEPTH ADJUSTMENT Disconnect plug from power source. Loosen the depth adjustment lever located between the guard and handle of saw. Hold the foot down with one hand and raise or lower saw by the Inner Scale Calibrated In Inches CALIBRATED DEPTH BRACKET Outer Scale Calibrated For Standard Lumber Sizes DEPTH ADJUSTMENT LEVERFIG. 3 60° MARK TO BE ADJUSTED PRIOR TO BEVEL ADJUSTMENT (60° ONLY) handle. Tighten lever at the depth setting desired. Check desired depth (Fig. 3). Not more than one tooth length of the blade should extend below the material to be cut, for minimum splintering (Fig. 4). FIG. 4 ONE TOOTH LENGTH SHOULD PENETRATE WOOD FOR MINIMUM SPLINTERING FIG. 5 BEVEL 90° CUTTING ANGLE CHECK ADJUSTMENT Disconnect plug from power source. Set foot to maximum depth of cut setting. Loosen bevel adjustment lever, set to 0° on quadrant, retighten lever and check for 90° angle between the blade and bottom plane of foot with a square (Fig. 5). Make adjustments by turning the small alignment screw, if necessary 90° FOOT (Fig. 6). BLADE LEVER ALIGNMENT SCREW FIG. 6 BEVEL ADJUSTMENT Disconnect plug from power source. The foot can be adjusted up to 45° by loosening the bevel adjustment lever at the front of the saw. Align to desired angle on calibrated quadrant. Then tighten bevel adjustment lever (Fig. 7). For 60° loosen depth adjustment lever, lower foot to 60° mark on depth bracket (Fig. 3), and tighten lever. Loosen bevel adjustment lever, depress 45° stop spring (Fig. 8), align foot to 60 mark on quadrant and tighten lever...