Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
FIG. 10 FOOT LOWER GUARD LIFT LEVER CUTTING LARGE SHEETS Large sheets and long boards sag or bend, depending on support. If you attempt to cut without leveling and properly supporting the piece, the blade will tend to bind, causing KICK-BACK and extra load on the motor (Fig. 11). Support the panel or board close to the cut, as shown in (Fig. 12). Be sure to set the depth of the cut so that you cut through the sheet or board only and not the table or work bench. The two-by-fours used to raise and support the work should be positioned so that the broadest sides support the work and rest on the table or bench. Do not support the work with the narrow sides as this is an unsteady arrangement. If the sheet or board to be cut is too large for a table or work bench, use the supporting two-by-fours on the floor and secure. FIG. 11 FIG. 12 WRONG RIGHT RIP CUTS The combination blade provided with your saw is for both cross cuts and rip cuts. Ripping is cutting lengthwise with the grain of the wood. Rip cuts are easy to do with a rip fence (Fig. 13). To attach fence, insert fence through slots in foot to desired width as shown and secure with the knob. FIG. 13 RIP FENCE KNOB DESIRED WIDTH OF CUT RIP BOARD GUIDE When rip cutting large sheets, the rip fence may not allow the desired width of cut. Clamp or nail a straight piece of 1" (25 mm) lumber to the sheet as a guide (Fig. 14). Use the right side of the foot against the board guide. FIG. 14 DESIRED LINE OF CUT RIP BOARD GUIDE -13 BM 2610945718 12-06 12/12/0BATTERY CHARGED CONDITION INDICATOR The battery is equipped with a charged condition indicator. By pressing the button ON, the charged condition can be checked when the battery is removed or when the machine is not in use. After approx. 5 seconds, the charged indicator switches off automatically. • • • When all three lights are illuminated, this indicates the battery pack is between 67% and 100% charged. • • When only two lights illuminate, this indicates the battery pack is between 33% and 66% charged. • When only one light illuminates, this indicates the battery pack is less than 33% charged. When one light blinks the battery pack is almost fully discharged. TEMPERATURE INDICATOR LIGHT The red indicator light signals whether the battery or tool (with battery inserted) is in the optimum temperature range. When the temperature is too high, the tool will not operate at full capacity. If the red indicator light illuminates continuously when the battery is inserted into the charger. The battery is outside the charging temperature range and cannot be charged. If the red indicator light blinks when the button or on/off switch (with battery inserted) is pressed, the battery is outside the operating range of -10 °C to +60 °C. When the temperature is above 70 °C the battery turns off until it’s in the optimum temperature range. BUTTON GREEN INDICATOR LIGHTS RED INDICATOR LIGHT Slide charged battery pack into the housing until the battery pack locks into position and the red warning label is no longer visible (Fig. 1). Your battery pack is equipped with a secondary locking latch to prevent the battery pack from completely falling out of the handle, should it become loose due to vibration. To remove the battery pack, press the battery pack release button and slide the battery pack away from housing. The red warning label will become partially visible. Press the battery pack release button again and slide the battery pack completely out of tool housing. INSERTING AND RELEASING BATTERY PACK If the indicator lights are “OFF”, the charger is not receiving power from power supply outlet. If the green indicator light is “ON”, the charger is plugged in but the battery pack is not inserted, or the battery pack is fully charged. If the green indicator light is “BLINKING”, the battery pack is being fast-charged. Fast- charging will automatically stop when the battery pack is fully charged. If the red indicator light is “ON”, the battery pack is too hot or cold for fast-charging. The charger will automatically switch to fast- charging once a suitable temperature is reached. If the red indicator light is “BLINKING”, the battery pack cannot accept a charge or the contacts of the charger or battery pack are contaminated. Clean the contacts of the charger or battery pack only as directed in these operating instructions or those supplied with your tool or battery pack. CHARGER INDICATORS, SYMBOLS AND MEANING BM 2610945718 12-06 12/12/06 12:21 PM Page 14 BM 2610945718 12-06 12/12/06 12:21 PM Page 15 IMPORTANT CHARGING NOTES 1. The charger was designed to fast charge the battery only when the battery temperature is between 32°F (0°C) and 140°F (60°C). If the battery pack is too hot or too cold, the charger will not fast charge the battery. (This may happen if the battery pack is hot from heavy use). When the battery temperature returns to between 32°F (0°C) and 140°F (60°C), the charger will automatically begin charging. 2. A substantial drop...