Assessments - 5, GPA: 3.6
(
)
)
|
Facilidade de uso
When changing the adjustment, change the height of the 8mm bolt (A) or the 8mm bolt (B) by turning them. (Fig. 8-a, Fig. 8-b) (For bevel scale) 8mm Bolt (B) (Stopper for left 45° bevel angle) 8mm Bolt (A) (Stopper for 0°) Fig. 8-a Fig. 8-b 2. Securing the workpiece WARNING: Always clamp or vise to secure the workpiece to the fence; otherwise the workpiece might be thrust from the table and cause bodily harm. 3. Installing the holders ... (Optional accessory) The holders help keep longer workpieces stable and in place during 6mm Wing Bolt the cutting operation. (Optional accessory) (1) As indicated in Fig. 9, use a steel square for aligning the upper edge of the holders with the base surface. Loosen the 6mm wing nut. Turn a height adjustment bolt 6mm, and adjust the height of the holder. (2) After adjustment, firmly tighten the wing nut and fasten the holder with the 6mm wing bolt (optional accessory). If the length of Height Adjustment Bolt 6mm is insufficient, spread a thin plate beneath. Make sure the end of Height Adjustment Bolt 6mm does not protrude from the holder. Bolt 6mm (Optional accessory) Fig. 9 Indicator Holder (Optional accessory) Steel Square Base Surface 6mm Wing Nut (Optional accessory) Height Adjustment English 4. Stopper for precision cutting ... (Stopper and holder are optional accessory) The stopper facilitates continuous precision cutting in lengths of Stopper 11" to 17-3/4" (280mm to 450mm). (Optional accessory) To install the stopper, attach it to the holder with the 6mm wing bolt as shown in Fig. 10. 6mm Wing Nut (Optional accessory) Height Adjustment Bolt 6mm (Optional accessory) Workpiece 6mm Wing Bolt (Optional accessory) Holder (Optional accessory) Move Fig. 10 5. Confirmation for use of sub fence …(Optional accessory) WARNING: In the case of left bevel cutting, remove the sub fence. Supposing it is not able to remove it, It will contact the blade or some part of the tool, causing in serious injury to operator. In the case of direct angle cutting and angle cutting, use the sub fence. The sub fence can be installed on the left side of the guide fence. Insert the rods of the sub fence into the holes in the guide fence. Tighten the 6mm wing bolt which come with the sub fence to secure the sub fence. Then, you can realize stable cutting of the material with a wide back face. Fig. 11 6. Position adjustment of laser line (Only Model C10FCH) WARNING: * Make sure before plugging the power plug into the receptacle that the main body and the laser marker are turned off. * Exercise utmost caution in handling a switch trigger for the position adjustment of the laser line, as the power plug is plugged into the receptacle during operation. If the switch trigger is pulled inadvertently, the saw blade can rotate and result in unexpected accidents. * Do not remove the laser marker to be used for other purposes. CAUTION: Sub Fence 6mm Wing Bolt Fig. 12 Fig. 13 English * Laser radiation- Do not stare into beam. * Laser radiation on work table. Do not stare into beam. If your eye is exposed directly to the laser beam, it can be hurt. * Do not dismantle it. * Do not give strong impact to the laser marker (main body of tool); otherwise, the position of a laser line can go out of order, resulting in the damage of the laser marker as well as a shortened service life. * Keep the laser marker lit only during a cutting operation. Prolonged lighting of the laser marker can result in a shortened service life. * Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. NOTE: * Perform cutting by overlapping the ink line with the laser line. * When the ink line and the laser line are overlapped, the strength and weakness of light will change, resulting in a stable cutting operation because you can easily discern the conformity of lines. This ensures the minimum cutting errors. * In outdoor or near-the-window operations, it may become difficult to observe the laser line due to the sunlight. Under such circumstances, move to a place that is not directly under the sunlight and engage in the operation. * Do not tug on the cord behind the motor head or hook your finger, wood and the like around it; otherwise, the cord may come off and the laser marker may not be lit up. Ink lining can be easily made on this tool to the laser marker. A switch lights up the laser marker. (Fig. 14) Depending upon your cutting choice, the laser line can be aligned with the left side of the cutting width (saw blade) or the ink line on the right side. The laser line is adjusted to the width of the saw blade at the time of factory shipment. Adjust the positions of the saw blade and the laser line taking the following steps to suit the use of your choice. (1) Light up the laser marker and make a groove of about 3/16" (5mm) deep on the workpiece that is about 1-1/2" (38mm) in height and 3-1/2"(89mm) in width. Hold the grooved workpiece by vise as it is and do n...
Este manual também é adequado para os modelos :Jig Saw e - C10FCH (1.62 mb)