Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Failure to do so could result in possible serious personal injury. BLADE WRENCH HOLDER A blade wrench (5 mm hex key) is packed with your saw. A convenient feature on your saw is the wrench holder. This is a slot located on the bottom portion of the saw handle. It is convenient for storing the wrench when it is not being used. BLADE SELECTION Your saw is equipped with a "lock-off" button which reduces the possibility of accidental starting. The lock-off button is located on the handle above the switch trigger. You must depress the lock-off button in order to pull the switch trigger. The lock resets each time the trigger is released. Note: You can depress the lock-off button from either the left or right side. SWITCH To turn your saw ON, depress the lock-off button and pull switch trigger. Release switch trigger to turn your saw OFF. VARIABLE SPEED This tool has a variable speed switch that delivers higher speed with increased trigger pressure. Speed is controlled by the amount of switch trigger depression. APPLICATIONS (Use only for the purposes listed below) ¦ Cutting all types of wood products (lumber, plywood, paneling, composition board, and hard wood). ¦ Cutting masonite and plastic. ¦ Cutting drywall. ¦ Cutting metals such as sheet steel, pipe, steel rods, aluminum, brass, and copper. WARNING: Do not allow familiarity with your saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. To obtain the best performance from your saw it is important to select a specific blade for the particular application and type of material you wish to cut. By doing this you will get a smoother faster cut and prolong blade life. Replacement blades for this saw are available from your nearest Ryobi dealer. WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1. Page 6 Page 7 Fig. 1 FEATURES LOCK-OFF BUTTON SWITCH TRIGGER BATTERY PACK SAW BLADE BLADE WRENCH (5 mm HEX KEY) BASE (SHOE) ASSEMBLY LOCK-OFF BUTTON BLADE WRENCH HOLDER DEPRESS HERE TO PULL SWITCH TRIGGER Page 8 ASSEMBLY Fig. 2 Fig. 3 BLADE CLAMP SCREW BLADE CLAMP BLADE SAW BAR PIN BLADE CLAMP SCREW BLADE CLAMP HOLE HOLE IN SAW BLADE BLADE CLAMP n Loosen the blade clamp screw enough to permit the saw blade to be inserted between blade clamp and saw bar. Note: It is never necessary to remove the blade clamp screw from the blade clamp when installing or removing blade. n Align the hole in the shank of the blade and blade clamp with the pin in the saw bar, then seat both on the pin in the saw bar. n Tighten blade clamp screw securely. n Remove blade wrench and store it in wrench holder. n Replace battery pack. Note: There may be times when the blade clamp sticks to the saw bar and will not loosen enough to allow blades to be installed or removed. If this happens, loosen the blade clamp screw with the blade wrench, then tap lightly on the end of the blade wrench with a mallet. See Figure 4. BLADE CLAMP SCREW BLADE CLAMP SAW BAR BLADE WRENCH (5 mm HEX KEY) MALLET WARNING: Always remove battery pack from your saw when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury. TO REMOVE / ATTACH BATTERY PACK See Figure 2. TO REMOVE: n Locate latches on side of battery pack and depress both sides to release battery pack from your saw n Remove battery pack from your saw. TO ATTACH: n Place the battery pack in your saw aligning raised rib on battery pack with groove in saw's battery port. See Figure 2. n Make sure the latches on each side of the battery pack snap into place and battery pack is secured to saw before beginning operation. TO INSTALL SAW BLADE See Figure 3. n Remove battery pack. See Figure 2. WARNING: Failure to remove battery pack from saw could result in accidental starting causing possible serious personal injury. n Remove the 5 mm blade wrench provided with your saw from wrench holder. Note: Wrench holder is located in bottom portion of saw handle. See Figure 1. BATTERY PACK DEPRESS LATCH TO RELEASE BATTERY PACK BATTERY PORT LATCH BLADE WRENCH (5 mm HEX KEY) Fig. 4 OPERATION OPERATION LED FUNCTION OF CHARGER See Figure 5. LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK: ¦ Red LED lighted = Fast Charging Mode ¦ Green LED lighted = Fully Charged Battery Pack ¦ Yellow and Green LED Lighted = Control Charge or Possible Faulty Battery. CHARGING BATTERY PACK The battery pack for this tool has been shipped in a low charge condition to prevent possible problems....