Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
With wider material you must move the Blade across the material to cut it. Do not bear down on the material, use light downward pressure. If the material binds the blade, release the trigger. Keep your hands away from the Blade. When the cut is completed, raise the 10. blade assembly, wait for the Blade to stop turning, release the Hold Down Vise and remove the work material from the saw. The laser guide will not turn off 11. automatically. Turn the laser guide off using the switch on the side of the laser battery housing. This is important to prevent accidental eye exposure to the laser beam. Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation: Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning and Maintenance BEFORE EACH USE,1. inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. After Use,2. clean external surfaces of the tool with clean, moist cloth. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children’s reach. If the blade has become dirty, use a 3. blade cleaner (not included) to clean it. Dirty blades will bind more easily, and will more often overheat and burn the wood as it cuts. Overheated blades dull more easily. If the Blade has become dull, replace it. 4. Dull blades will cause increased tear-out and ragged edges on the cuts. Occasionally clean the Slides, rotating 5. Table components and other moving parts. Use a good quality dry lubricant (not included) which will not attract dust. To replace the laser Batteries: Slide the 6. cover off the laser housing as shown in the diagram above. Replace the batteries with two ‘AAA’ batteries and close the cover. CAUTION! To prevent injury, position batteries in proper polarity and do not install batteries of different types, charge levels, or capacities together. 7. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. WARNING Replacing the Blade To reduce risk of serious injury: Return guard to original position and secure in place after replacing blade. Unplug the tool from its power source.1. Lock the blade assembly in the raised 2. position by pushing in the Locking Pin. Loosen the Center Cover Fixing Bolt. 3. (See Figure 3.) Remove the Shoulder Screw (15). 4. (See Figure 4 and photo below.) Shoulder Screw Raise the Blade Guard and Center 5. Cover. (See Figure 5.) While holding in the Arbor Lock Button, 6. use the Wrench to loosen the Arbor Bolt by turning it clockwise. (See Figure 6.) Note: The Arbor Bolt has a left hand thread, so it loosens by turning clockwise. Remove the Arbor Bolt, Outer Flange 7. and Saw Blade by pulling them straight off the Arbor. WARNING Figure 5 Figure 3 Figure 6 Figure 4 REV 09j Reinstall a new Blade on the Inner 8. Flange (68A). (See Figure 7.) Be sure to match the direction marked on the new blade with the direction marked on the saw Blade Housing. Replace the Outer Flange and Arbor 9. Bolt. Tighten the Arbor Bolt securely using the Wrench by turning it counterclockwise. Rotate the Center Cover back into place 10. and tighten the Center Cover Fixing Bolt using the Wrench by turning it clockwise. Release the Locking Pin.11. Adjusting the Fence The Fence holds the work piece in a 1. fixed position while the Table and or the blade assembly are adjusted in a miter or bevel angle. To make accurate cuts, the Fence must 2. be perpendicular (at a 90. angle) to the Saw Blade. Before beginning work, make a test cut 3. on scrap material with the Table set at 90.. Check the cut with an accurate square. 4. You can also reverse the two pieces, hold the cut ends together, and hold a good straight edge along the side of the pieces. If either test reveals that the cut is not 5. a true 90. angle, you must adjust the Fence before beginning work. To adjust the Fence, first unplug the tool.6. Lower the blade assembly and lock it in 7. place using the Locking Pin. Lay a reliable carpenter’s square on 8. the table with one edge along the blade and the other along the Fence. Any inaccuracy should be visible. NOTE: The square must contact the surface of the blade, not the teeth, for an accurate reading. The Fence is held in place with bolts at 9. each end. Loosen the bolts slightly, and gently tap the Fence into position using a soft mallet. Retighten the bolts and make another test cut. Repeat the process until the Fence i...