Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Never attempt to discharge a tool’s battery by continuing to pull the tool trigger. When tool performance begins to diminish, stop the tool, recharge the battery and use the fresh battery for optimal performance. 1. When a Battery (47) requires recharging, a 3 to 5 hour* charge allows the tool to operate at full power. Do not recharge the Battery longer than 5 hours*, as damage to the Battery and/or tool will occur. 2. To charge the Battery (47), plug the AC Charger Adapter’s (53) plug into the Charger (52). Insert the Charger (52) onto the top of the Battery (47) until it locks into place. Charging room temperature: 50° F - 104° F. Then, plug the AC Charger Adapter into the nearest 120 Volt, grounded, electrical outlet. (See illustration below.) 3. Two Charging Indicator LEDs on the Charger (52) will illuminate to show that charging is taking place. NOTE: The AC Charger Adapter (53) will not automatically turn off when the Battery is fully charged, and the Charging Indicator LEDs will remain on until the AC Charger Adapter is disconnected from the electrical outlet. Recharging the Battery more than 5 hours* can cause damage to the battery cells. 4. While charging, the Battery (47), AC Charger Adapter (53), and/or Charger (52) may become warm to the touch. This is normal, and does not indicate a problem. 5. Once the Battery (47) is fully charged, disconnect the AC Charger Adapter (53) from the electrical outlet. Then, disconnect the Charger from the Battery. * The Battery (47) require an initial charge time of 8 hours. Do not recharge the Battery more than 5 hours after this initial charging. SKU 93830 For technical questions, please call 1-800-444-3353. Page 10 OPERATION Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagrams at the end of the manual. Reciprocating Saw WARNING: Always make sure the Battery (47) of the Reciprocating Saw is removed prior to making any adjustments to the tool. 1. Slide the Battery (47) into the base of the Reciprocating saw. Note: Do not start the Reciprocating Saw if the Saw Blade (23) is in contact with anything before operation. If necessary, lift the Reciprocating Saw to free the Saw Blade before squeezing the Trigger. 2. NEVER cut into areas where you cannot identify any possible hazards behind or inside the surface being cut. 3. Hold the Reciprocating Saw firmly with both hands, then slide the Safety (37) to one side and squeeze the Trigger (41) to start the Saw. 4. With the Reciprocating Saw “ON”, place the Saw Blade (23) against the material to be cut. Press down slightlyon the Reciprocating Saw to help it cut, but allow the saw to do the work. 5. Once the cutting procedure is completed, release pressure on the Trigger (41) to stop the Reciprocating Saw. Then, remove the Battery (47). 6. Saw Blade Installation/Replacement: A. Remove the Battery (47) from the tool. B. With a Hex Wrench (not provided), loosen the front Cap Screw (29). (See illustration above.) C. Slide the Saw Blade (23) teeth-down into the Blade Holder (28) as far as possible. D. Then, firmly retighten the Cap Screw (29) to secure the Saw Blade (23) in place. E. Gently pull on the Blade (23) with a gloved hand to ensure it is held properly. SKU 93830 For technical questions, please call 1-800-444-3353. Page 11 INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Always remove the Battery Pack (47) from a tool and unplug the AC Charger Adapter (53) from its electrical outlet before performing any inspection, maintenance, or cleaning on the tool. 2. BEFORE EACH USE, inspect the general condition of the tool. Check for misalignment or binding of moving parts, cracked or broken parts, damaged wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs with a tool, have the problem corrected before further use. Do not use damaged equipment. 3. TO CLEAN, use a clean, slightly damp cloth to clean the outer surfaces of the tool. A mild detergent may be used. Do not use solvents. Do not immerse the tool, Battery, or AC Charger Adapter in water. 4. WHEN STORING, always keep this tool and accessories in a clean, dry location out of reach of children. Keep charger unplugged from the wall outlet when not in use. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR H...