Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
13. Make sure the Cutting Wheel Blade (8) is wet at all times when cutting. 14. When operating the Tile Saw, always make sure to fill the Tray (17) with enough clean, cold water to cover the lower edge of the Cutting Wheel Blade (8), but not so deep as to spill over the edge of the Tray. Make sure the water supply for the Tile Saw is not dirty, sandy, and does not contain any corrosive chemical products. Change the water when necessary while in use and rinse out the Tray (17) after every use. 15. Keep hands and fingers away from the cutting area and Cutting Wheel Blade (8). Use a “push stick” (not included) if necessary. 16. Check Blade Guard (49) for proper up/down movement before each use. Do not operate the Tile Saw if the Blade Guard does not move freely. Make sure the Blade Guard moves freely and does not touch the Cutting Saw Blade (8) or any other part of the Tile Saw, in all angles and depths of cut. 17. Make sure the Tile Saw is located on a flat, level, sturdy surface capable of supporting the weight of the Tile Saw, workpieces, and any additional tools. 18. Use the Tile Saw only for cutting ceramic tile, quarry tile, marble, terra cotta, and slate with a maximum thickness of 1 inch. 19. Do not use the Tile Saw for cutting metals or for cutting curves. 20. Before using the Tile Saw, make sure the Cutting Wheel Blade (8) is properly mounted on the Saw Arbor. Make sure the Blade is balanced, and is not cracked or bent. 21. The Cutting Wheel Blade (8) will become hot while cutting. Allow the Blade to completely cool before handling. 22. Allow the Cutting Wheel Blade (8) to spin up to full speed before feeding a workpiece into it. When turning off the Tile Saw, allow the Cutting Wheel Blade to spin down and stop on its own. Do not press against the Blade to stop it. SKU 40315 For technical questions, please call 1-800-444-3353. Page 6 TILE SAW 23. Do not force the workpiece into the Cutting Wheel Blade (8) when cutting. Apply moderate pressure, allowing the Blade to cut without being forced. 24. Turn off the Tile Saw and allow the Cutting Wheel Blade (8) to stop on its own if the Blade is to be backed out of an uncompleted cut. 25. Never attempt to cut more than one tile at a time. 26. Never attempt to cut freehand. Make sure the tile to be cut is pressed firmly against the Cutting Guide (57). 27. Make sure the Table (51) and surrounding area are clear with the exception of the tile to be cut. 28. Keep all electrical connections dry and off the ground. 29. Always arrange a “drip loop” in the Power Cord (34) connecting the Tile Saw to a 120 volt, grounded, electrical outlet. A drip loop is that part of the Power Cord below the level of the outlet, or the connector if an extension cord is used, to prevent water from traveling along the Power Cord and coming in contact with the outlet. If the Power Plug or electrical outlet does get wet, do not unplug the Power Cord. Disconnect the fuse or circuit breaker that supplies power to the outlet. Then, unplug and examine for presence of water in the outlet. (See Figure A.) POWER CORD/PLUG (34) 120 VOLT GROUNDED ELECTRICAL OUTLET DRIP LOOP FIGURE A SKU 40315 For technical questions, please call 1-800-444-3353. Page 7 30. Avoid splashing water on the Motor (42), Power Switch (21), Power Cord/ Plug (34), or any other electrical component. 31. Make sure to stand on a dry, insulated surface such as a rubber mat while using the Tile Saw. 32. Never attempt to stand on the Tile Saw. Doing so may cause the Saw to tip, causing personal injury and/or property damage. 33. Turn off the Tile Saw, unplug its Power Cord/Plug (34) from its 120 volt, grounded, electrical outlet, and allow the tool to completely stop prior to performing any inspection, maintenance, or cleaning on the unit. 34. Use the right tool or attachment for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this product was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not intended. 35. People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to WARNING! a heart pacemaker could cause interference or failure of the pacemaker. 36. WARNING! Some dust created by power sanding, sawing, grinding, drill ing, and other construction activities, contain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safet...