Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Diagram.) Caution: Prior to installing the Moveable Cover (43), make sure the Compound Miter Saw is disconnected from its electrical power source. Use the lock button Plastic Ball (51) to secure the saw arm in its lowered position. Locate the two Hex Head Screws (45) on the frame. Use the wrench provided to remove the front screw, and to loosen the rear screw a few turns. Use a cross head screwdriver (not included) to remove Screw (39) and Roller (33) from the guard assembly. Hold the blade guard assembly with the plastic cover down. With your other hand, rotate the spring plate clockwise approximately one turn so there is tension on the spring. Catch the rear slot in the plate under the head of rear Screw (45). Then align the holes, and install the front Screw. Tighten both, and release the guard carefully. Check to make certain that the rear (forked) end of bar (40) is under the head of the screw that guides it. Now release the lock button plastic ball (51), and raise the saw arm. Align the forward slot in bar (40) with the threaded brass bushing in the spring plate. Install screw (39) and roller (33) through the slot and into the bushing. Check that all screws are tightened and for correct operation of the guard. It should move downward to cover the blade as the saw is lowered. Rev 08/06 To Attach The Moveable Bar: Caution: Prior to installing the Moveable Bar (40), make sure the Compound Miter Saw is disconnected from its electrical power source. Temporarily remove the Upper Screw (39) and Upper Roller Sheath (33). (See Figure F, and Assy. Diagram.) Temporarily remove the Lower Screw (39) Slide the lower slot of the Moveable Bar (40) beneath the Lower Roller (31) and let the slot rest upon the Lower Roller Sheath (33). (See Figure F, and Assy. Diagram.) Align the upper slot of the Moveable Bar (40) with the threaded mounting hole as shown in Figure F. Replace and tighten the Upper Screw (39) and Upper Roller Sheath (33) through the upper slot of the Moveable Bar (40). (See Figure F, and Assy. Diagram.) Insert the Lower Screw (39) through the middle mounting hole of the Moveable Bar (40) and tighten the Screw. (See Figure F, and Assy. Diagram.) To Attach The Dust Bag: Caution: Prior to attaching the Dust Bag (54), make sure the Compound Miter Saw is disconnected from its electrical power source. Use the spring clamp on the Dust Bag to secure the Dust Bag (54) to the Exhaust Outlet on the Frame (50). (See Figures D, E, and Assy. Diagram.) When the Dust Bag (54) is half full remove it from the Compound Miter Saw, and empty it. NOTE: You may also attach a hose from a shop vacuum (not provided) to the Exhaust Outlet on the Frame (50) for more efficient dust collection. (See Figures D, E, and Assy. Diagram.) OPERATING INSTRUCTIONS WARNING: Ensure that this item is completely and properly assembled before use. Use of this item without all guards and/or safety devices in place can result in serious Personal injury or DEATH. NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 18 of this manual. The Power Switch: To turn on the Compound Miter Saw, push in the Safety Button and squeeze the Power Switch (82). To turn off the Compound Miter Saw, release pressure on the Power Switch. (See Figure G, and Assy. Diagram.) DOWN HANDLE (#83) POWER SWITCH (#82) FIGURE GSAFETY BUTTON To Lower The Saw Blade: NOTE: The Compound Miter Saw automatically locks in place in the up position. To lower the Saw Blade (70), pull out on the Plastic Ball (51), and pull down on the Handle (parts #80, #83). (See Figure H, and Assy. Diagram.) PLASTIC BALL (#51) (PULL OUT TO LOWER SAW BLADE) LONG SCREW (#37) FIGURE H REV 05/05 To Make A Basic 90 Degree Cut: Properly position the wood stock against the Location Board (23). (See Figure I, and Assy. Diagram.) LOCATION BOARD (#23) SUPPORT FEET (#10)BASE (#12) FIGURE IPlug the Power Cable (93) into a grounded, three prong, 120 Volt, electrical outlet. Pull out on the Plastic Ball (51), and pull down slightly on the Saw Handle (80, 83). (See Figure H, and Assy. Diagram.) Squeeze the Power Switch (82) to power the Compound Miter Saw. Allow the Saw Blade (70) to reach its maximum speed before starting the cut. (See Figures E, G, and Assy. Diagram.) Lower the Saw Blade (70) into the wood stock, pressing gently down. Do not force the tool. Allow the Saw Blade to do its work as you feed it into the wood stock. Continue with the cut until completed. Do not stop midway. (See Figure E, and Assy. Diagram.) When the cut is completed, release the Power Switch (82) and wait for the Saw Blade (70) to stop turning before raising the Saw Blade to its up position. (See Figures E, G, and Assy. Diagram.) Remove the cut wood stock from the Compound Miter Saw, and unplug the tool from its electrical power supply outlet. To Adjust The Angle Of The Cut: 1. Caution: Prior to adjusting the angle of the cut, make sure the Compound Miter Saw is disconnected from its electrical po...