Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
See Tools Electric in yellow pages. 5. The power pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using saw with its power pack in a depleted condition. 6. To prolong power pack life, avoid leaving the power pack on charge for more than 8 hours. Although overcharging is not a safety concern, it can significantly reduce overall power pack life. 7. When the battery is inserted into the charger, the red “Charging Indicator” light will come on indicating that there is contact between the battery and charger. The light will stay on as long as the battery is in the charger and the charger is plugged into a working outlet. It WILL NOT flash, go out or change to a different color when the charging cycle is complete. Battery cap information Battery storage and carrying caps are provided for use whenever the battery is out of the tool or charger. Remove cap before placing battery in charger or tool. WARNING! Do not store or carry battery so that metal objects can contact exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap. Without cap in place, battery could short circuit causing fire or burns or damage to battery. 8 Blade Lame Disco Inner clamp washer Rondelle de fixation externe Roldana de sujecion exterior Saw spindle Arbre de la scie Flecha de la sierra Blade clamping screw Vis de fixation de la lame Tornillo de sujecion del disco Outer clamp washer Rondelle de fixation externe Roldana de sujecion interior Direction of teeth Sens des dents Direccion de los dientes Kerf Plate and Screw Placa indicadora de corte y tornillo For pocket cuts only Pour coupes en retrait seulement Solamente para cortes de bolsillo 10 1 2 Correct Correct Correcto Wrong Incorrect Incorrecto Material bends on blade causing heavy loads or kickback Le materiau plie au contact de la lame causant de lourdes surcharges ou des rebonds. El material oprime el disco ocasionando sobrecarga o contragolpe Support work near cut Soutenir la piece pres de la ligne de coupe. Apoye la pieza cerca del corte 3 4 Correct Correct Correcto Wrong Incorrect Incorrecto 5 6 7 Bevel adjustment knob Bouton de reglage pour coupes en biseau Perilla de ajuste de bisel Depth adjustment lever Bouton de reglage de la profondeur Perilla de ajuste de profundidad Tip of tooth Bout de la dent Surface of wood Punta del diente Surface du bois Superficie de madera Proper depth: one tooth below surface of wood Profondeur appropriee : une dent sous la surface du bois. Profundidad correcta: un diente debajo de la superficie de madera Switch Handle Poignee de l’interrupteur Mango del interruptor Warning: When blade starts cutting, release retraction lever immediately Avertissement : Lorsque la lame commence a decouper, relacher immediatement le ressort de rappel. Advertencia: Cuando el disco inicie el corte, suelte inmediatamente la palanca del mecanismo retractil Tighten Serrer Apriete Loosen Desserrer Afloje 9A 9B Blade Wrench Cle de reglage de la lame Llave del disco Switch lock-off lever Levier de verrouillage en position «arret» Palanca de seguro de apagado Switch trigger Interrupteur a gachette Interruptor de gatillo Assembly/Adjustment Set-Up WARNING: Always remove battery from tool before any of the following operations. Attaching and removing the Blade NOTE: The first time the blade bolt is removed from saw without a blade installed, it may be necessary to place the blade wrench on the bolt head and tap it sharply in the counter clockwise direction. Retract lower guard and assemble blade and clamp washers, as shown in Fig. 8. To prevent blade rotation while tightening the blade clamping screw, raise the lower guard and place the saw down on a piece of scrap wood as shown in Fig. 9A. The blade teeth will dig into the scrap wood and prevent rotation while you tighten the blade clamping screw. Tighten the blade clamping screw securely, using the wrench provided. Figure 9B illustrates an alternative method of loosening and tightening the blade by inserting a screwdriver through the hole in the blade to prevent it from moving. NOTE: The blade wrench is stored in the kerf plate as shown in Fig. 8. Cutting Depth Adjustment Adjust depth of cut using depth adjustment lever. See (Figs. 5 & 6) for proper setting. Tighten lever securely. Bevel Angle Adjustment Adjust bevel angle (Fig. 7) using bevel adjustment knob and bevel scale. Tighten knob securely. Kerf Plate Adjustment Adjust kerf plate (Fig. 8) to read zero when the bevel scale reads zero by loosening the kerf plate screw and sliding the plate as necessary. Align mark on kerf plate with drawn pencil line and advance blade into cut. The kerf plate has lines for zero bevel and 45 degree bevel cutting. A B Battery Cap Operating Instructions WARNING: To reduce the risk of serious personal injury, read, understand and follow all ...
Este manual também é adequado para os modelos :Jig Saw e - 609747-21 (306.76 kb)
Jig Saw e - BDCS1400 (306.76 kb)
Jig Saw e - CS144 (306.76 kb)
Jig Saw e - CS180 (306.76 kb)