Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
II Medium orbit cutting action For cutting wood and plywood. For fast cutting in aluminum and mild steel. III Large orbit cutting action For fast cutting in wood and plywood. 1 2 1. Lock-off button 2. Switch trigger 002708 Switch action CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To prevent the switch trigger from being accidentally pulled, a lock-off button is provided. To start the tool, depress the lock-off button and pull the switch trigger. Release the switch trigger to stop. 002711 Speed adjusting dial The tool speed can be infinitely adjusted between 500 and 2,800 strokes per minute by turning the adjusting dial. Higher speed is obtained when the dial is turned in the direction of number 5; lower speed is obtained when it is turned in the direction of number 1. Refer to the table to select the proper speed for the work- piece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced. 1 1. Speed adjusting dial Workpiece to be cut Workpiece to be cut Wood 3 - 5 Mild steel 3 - 5 Stainless steel 3 - 4 Aluminum 2 - 3 Plastics 1 - 4 CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded and heated up. • The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing saw blade CAUTION: • Always clean out all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may cause insufficient tightening of the blade, resulting in a serious personal injury. • Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. • Always secure the blade firmly. Insufficient tightening of the blade may cause blade breakage or serious personal injury. To install the blade, loosen the screw counterclockwise on the blade holder with the hex wrench. 1 2 002717 1. Screw 2. Hex wrench 002718 With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the roller. Then tighten the screw clockwise to secure the blade. To remove the blade, follow the installation procedure in reverse. NOTE: • Occasionally lubricate the roller. 002725 6.35mm(1/4”) 1. Blade holder 2. Bolt 1 2 002726 Installing the universal shank jig saw blade If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.35 mm (1/4”). Insert the blade into the blade holder as far as it will go. Make sure that the end of the blade shank reaches the bottom of the inner slit and tighten the bolt securely with the hex wrench. 002733 Anti-splintering device For splinter-free cuts, the anti-splintering device can be used. To install the anti-splintering device, move the base all the way forward and fit it into the base from the back of base. NOTE: • The anti-splintering device cannot be used when making bevel cuts. 1 2 3 1. Screw 2. Roller 3. Jig saw blade 1 2 1. Base 2. Anti-splintering device 1 2 3 1 2 3 Screw 2. Plastic base plate 3. Hex wrench 002735 Plastic base plate (optional accessory) Use the plastic base plate when cutting decorative veneers, plastics, etc. It protects sensitive surfaces from damage. To replace the base plate, remove the four screws. 1 2 3 1. Hex wrench 2. Rip fence (Guide rule) 3. Bolt 002737 Rip fence (optional accessory) When cutting widths of under 150 mm (5 - 29/32”) repeatedly, use of the rip fence (guide rule) will assure fast, clean, straight cuts. To install it, loosen the bolt on the front of the base. Slip in the rip fence and secure the bolt. 1 2 3 1. Threaded knob 2. Circular guide 3. Pin 002739 Circular guide (optional accessory) Use of the circular guide insures clean, smooth cutting of circles under 200 mm (7 - 7/8”) in radius. Insert the pin through the center hole and secure it with the threaded knob. Move the base of the tool forward fully. Then install the circular guide on the base in the same manner as the rip fence (guide rule). 1 2 3 1. Notches 2. Base 3. Plastic cover 002740 Plastic cover and vacuum head (optional accessory) The vacuum head is recommended to perform clean cutting operations. Install the plastic cover on the tool by fitting it into the notches in the tool. 1 2 1 2 Vacuum head 2. Base 002741 To attach the vacuum head on the tool, insert the hooks of the vacuum head into the hole in the base. The vacuum head can be installed on either left or right side of...
Este manual também é adequado para os modelos :Jig Saw e - 4333D (221.88 kb)