Assessments - 3, GPA: 4 ( )

Fabricante : Dolmar Arquivo Tamanho: 3.5 mb Arquivo Nome : Língua de Ensino:

Keep an eye out for animals as well (9). - Before starting work the Power Cut must be checked for perfect function and operating safety according to the prescriptions. In particular, make sure that the cutting wheel is in good condition(replace immediately if torn, damaged or bent), the cutting wheel is properly mounted, the protective hood is locked in place, the hand guard is properly mounted, the V-belt has the proper tension, the throttle moves easily and the halfthrottle lock button functions properly, the grips are clean and dry, and the combination switch functions properly (Start/Stop (I/O) switch, choke). - Start the Power Cut only after complete assembly and inspection. Never use the Power Cut when it is not completely assembled. 7 6 5 9 8 30 m 3 meters = wearing Protective Equipment Cutoff discs - The protection hood must always be on! Change discs only with the engine off! Cutoff discs -The protection hood must always be on! Change discs only with the engine off! WARNING! Never use carbide tipped, circular saw blades or any kind of wood cutting blades. Never cut any type of wood. Reactive forces can cause severe personal injury from blade contact or thrown tips. NOTE:Whenusingdiamondcutoffdiscs,alwaysmakesuretoobserve the "direction of rotation" markings. Diamond discs should only be used for cutting masonry/brick/ concrete etc. -Cutoff discs are intended only for radial loading, i.e. for cutting. Do not grind with the sides of the cutting disc! This will break the disc (10)! Caution! Never change direction (turning radius less than 5 meters / 5 1/2 yards), exert lateral (sideways) pressure, or tip the Power Cut during cutting (11)! -Useacuttingdisconlyforcuttingthematerialsitisintendedfor.The proper type of disc must be used, for either metals or masonry. -The arbor hole of the cutting disc must be an exact fit with the arbor or shaft. If the arbor hole is larger, it must be fitted with an adapter ring (available as an accessory). -The cutting disc must be rated for freehand cutting at up to 3850 rpm or 80 m/sec for 400 mm discs, 4370 rpm or 80 m/sec for 350 mm discs, or up to 5100 rpm or 80 m/s for 300 mm discs. Use onlycutting discs that comply with EN 12413, EN 13236. -The disc must be free of defects (12). Do not use defective cutting discs. Always tighten the cutting disc mounting bolt to a torque of 30 Nm. Otherwise, the cutting disc can twist. -Before starting the cutting disc, make sure you have a steady footing. -Put the Power Cut into operation only as described in this instruction manual (13). Always place your left foot in the rear handle and grasptheotherhandlefirmly(withthumbandfingers).Otherstarting methods are not allowed. -WhenstartingthePowerCut itmustbewellsupportedandsecurelyheld. The cutting disc must not be touching anything. -If the cutting disc is new, test it by running it at least 60 seconds at topspeed.Whendoingthis,makesurethatnopersonsorbodyparts are in the extended swing range of the disc, in case it is defective and flies apart. -When working with the Power Cut always hold it with both hands. Take the back handle with the right hand and the tubular handle with the left hand. Hold the handles tightly with your thumbs facing your fingers. -CAUTION: When you release the throttle lever the disc will keep spinning for a short period of time (free-wheeling effect). -Continuously ensure that you have a safe footing. -Hold the Power Cut such that you will not breathe in the exhaust gas.Donotworkinclosedroomsorindeepholesorditches(danger of poisoning by fumes). -Switch off the Power Cut immediately if you observe any changes in its operating behavior. -Switch off the engine before inspecting the V-belt tension or tighteningit,replacingthecuttingwheel,repositioningthecutter attachment (side or middle position) or eliminating faults (14). -Turn off the engine immediately and check the disc if you hear or feel any change in cutting behaviour. -Turn off the Power Cut when taking a break or stopping work (14). Place the unit in such a way that the disc is not touching anything and cannot endanger anyone. -Do not put the overheated Power Cut in dry grass or on any inflammable objects. The muffler is very hot (danger of fire). -IMPORTANT:After wet cutting, first turn off the water feed and then let the disc run at least 30 seconds, to fling off the remaining water and prevent corrosion. 14 10 11 12 min. 5 m 13 . Maintenance . Refuelling . Changing cutoff discs . Repositioning thecutting attachment . Stopping work . Transport . Putting out of function Kickback and lock.in - When working with the Power Cut there is a danger of kickback and lock.in. - Kickback occurs when the top of the cutting disc is used for cutting (15). - This causes the Power Cut to be thrown back toward the user with great force and out of control. Risk of injury! To prevent kickback, observe the following: - Never cut with the section of the cutting disc shown in figure 15. Be especially careful when reinser...

Baixe o seu

Para fazer o download, introduza 2 dígitos :