Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
19. Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly. If adjustment cannot be achieved with adjusting nuts (C), consult with your Echo Dealer for correct adjustment procedure. Tighten nuts (C). 20. Connect 2 ignition stop leads (A,B) from throttle cable tubing to 2 ignition leads (A,B) on engine. 21. Gather ignition wires and position behind air filter case. 22. Install air filter and cover Install Hip Pad (Optional) 1. Attach hip pad to harness as shown. A B A B D C U-Handle Kit installation instrUctions Balance and Adjust Unit 1. Loosen harness clamp screw. 2. Put on harness and attach unit to harness. 3. Slide harness clamp (L) up or down until unit balances with head approximately 50-75 mm (2 -3 in.) from the ground. 4. Tighten harness clamp screw. 5. Loosen upper U-Handle clamp screws (N), and position U-Handle for comfortable operation. 6. Tighten U-Handle clamp screws and 8 mm clamp bolt securely. L N NOTE In case of Emergency, the trimmer/brushcutter can be released from the harness by pulling up on the quick-release collar. ecHo consUmer prodUct sUpport If you require assistance or have questions concerning the application, operation or maintenance of this product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to 4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit to help your Consumer Product Support Representative. ECHO, INCORPORATED 400 OAKWOOD ROAD LAKE ZURICH, IL 60047 USA PHONE: 1-800-673-1558 instrUcciones para la instalacion del conjUnto de co version de los agarradores-U N/P 99944200689 Para los Modelos: SRM-280/280S/280T S/N TODOS ADVERTENCIA Debe instalar un juego de la barrera de barra o empunadura en ‘U’ y un juego de conversion de hojas antes de operar esta unidad usando hojas, ya que de lo contrario se pueden producir lesiones graves. IMPORTANTE Si se usan cabezas de un solo filamento que no son estandar, hojas o cultivadores de METAL/PLASTICO etc., SE DEBE REAJUSTAR EL CARBURADOR o se produciran danos importantes en el motor. Vea “Ajuste del carburador” en el manual del operador de la unidad. GUIA DE CONFIGURACION DE LAS HOJAS DE SRM/PAS/SB* PARA USAR ESTAS HOJAS Cortadores de plastico para hierba/ maleza Pro Maxi-Cut Hoja de plastico rigida Tri- Cut para hierba/ maleza Hoja de 8 dientes de metal/ Tri-Cut para hierba/ maleza Hoja desbrozadora DE metal 80T / Hoja de sierra de metal para desmonte 22T .Usted debe instalar estas piezas! Empunadura Asa con o sin barra de barrera Asa con barra de barrera, o empunadura en “U” La asa con la barra de barrera, o la empunadura en “U” La empunadura en “U” Protector contra residuos Protector de metal Protector de metal Protector de metal Protector de metal Arnes Arnes para el hombro Arnes para el hombro Arnes para el hombro Arnes para el hombro**** Tornilleria de montaje de la hoja Placa superior ...
Este manual também é adequado para os modelos :Jig Saw e - U-HANDLE SRM-280T (488.77 kb)
Jig Saw e - U-HANDLE SRM-280S (488.77 kb)