Assessments - 3, GPA: 4
(
)
)
|
Fotos e especificações Bosch PKS 40 |
Facilidade de uso
+ When cutting spruce lengthways, long spi- ral chips are formed. Beech and oak dusts are especially detrimental to health. Therefore, work only with dust extrac- tion. Operating Instructions 14 • 2 610 392 415 • TMS • 28.11.02mikosoft praha s.r.o. mikosoft praha s.r.o. Clean the saw blade and all the clamping parts to be assembled. Tilt back the retracting blade guard 9 and hold firmly. Place the saw blade onto the mounting flange 21. Integrated Dust Extraction For small jobs, work with the dust bag (accessory). Insert the dust bag connection piece into the dust ejector 3. Empty the dust bag regularly to maintain an optimum vacuuming function. II II 2 610 392 415 - Buch Seite 5 Dienstag, 10. Dezember 2002 7:52 07 Parallel Guide (see figure ) The parallel guide 10 enables exact cuts along a work piece edge and cutting strips of the same di- mension. Sawing with an Auxiliary Guide (see figure ) For cutting large work-pieces or straight edges: Clamp a board or strip tightly to the work-piece as an auxiliary guide using screw clamps. Guide the base plate along the auxiliary guide. Guide Rail (accessory) (see figure ) The guide rail 25 enables particularly exact cut- ting, both vertically and mitred to 45°. The adhesive coating prevents the guide rail from slipping and protects the surface of the work piece. The hard anodised coating of the guide rail – Make sure that the guide rail is not sawn into (Fig. II and III). – Tighten the winged screw for the parallel guide 14 to ensure a firm connection between the guide adapter 24 and the circular saw. – Remove the circular saw from the guide rail 25. – Place the guide rail on the workpiece in such a way that the rubber lip lies exactly along the cutting edge (marked line) and tighten using screw clamps 23. Tips E 0°-Cut 1 – 45°-Cut 2424mikosoft praha s.r.o.mikosoft praha s.r.o. English - 5 Place the guide rail onto the work-piece pro- jecting slightly over the side. Make sure that the end with the rubber lip is directed towards the saw blade (Fig. I). – Place the circular saw premounted guide-rail adapter 24 onto the guide rail 25 and set the cutting angle and cutting depth. – Align the circular saw with the guide adapter 24 in such a way that the teeth of the saw blade lie against the edge of the rubber lip. n Before any work on the machine itself, pull the mains plug. + For safe and proper working, always keep the machine and the ventilation slots clean. The retracting blade guard must always be able to move freely and freely and retract automati- cally. Therefore, always keep the area around the retracting blade guard clean. Remove dust and chips by blowing out with compressed air or with a brush. Saw blades that are not coated can be protected against corrosion with a thin coat of acid-free oil. Before use, the oil must be removed again, oth- erwise the wood will become soiled. Resin and glue residue on the saw blade produce poor cuts. Therefore, clean the saw blade imme- diately after use. I Maintenance and Cleaning 15 • 2 610 392 415 • TMS • 28.11.02mikosoft praha s.r.o. mikosoft praha s.r.o. – allows the circular saw to glide easily. The rubber lip on the guide rail serves as a splinter guard, which avoids fraying of the surface when sawing wooden materials. For this, the teeth of the saw blade must lie directly against the rubber lip. Working with the guide rail 25 is possible only . + with use of the guide-rail adapter 24 (accessory). For exact cuts using the guide rail 25 the following working steps must be carried out again: The guide rail 25 must not protrude over the workpiece on the side of the cut. – Position the saw, ensuring that the guide-rail adapter 24 is seated firmly. – Saw through the material, applying moderate and steady feed. Note: Two guide rails can be connected to one with use of the connection piece 26 (accessory). Clamping is carried out with the four screws located in the connection piece. III F B 3 2 1 2 610 392 415 - Buch Seite 6 Dienstag, 10. Dezember 2002 7:52 07 If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools. In all correspondence and spare parts orders, please always include the 10-digit order number given on the nameplate of the machine. WARNING! Important instructions for con- necting a new 3-pin plug to the 2-wire cable. The wires in the cable are coloured according to the following code: Do not connect the blue or brown wire to the earth terminal of the plug. Important: If for any reason the moulded plug is removed from the cable of this machine, it must 23 Screw clamps, pair........................ 1 607 960 008 24 Guide-rail adapter .......................... 2 607 001 375 25 Guide rail (1.4 m long) ................ 2 602 317 031 Guide rail (0.7 m long) ................ 2 602 317 030 26 Connection piece ........................... 1 602 319 003 27 Dust bag with adapter ................. 1 605 411...
Este manual também é adequado para os modelos :Jig Saw e - PKS 46 (2.9 mb)