Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
CAUTION — RECHARGEABLE DEVICES • Certain rechargeable devices are designed to be charged by plugging them directly into an AC receptacle. Thesedevices may damage the inverter or the charging circuit. • If there is any sign that your appliance is behaving differently to that when connected to the normal power sourcethen unplug and seek advice from your appliance manufacturer. • This problem does not occur with most of the battery-operated equipment. Most of these devices use a separatecharger or transformer that is plugged into an AC receptacle. • The inverter is capable of running most chargers and transformers. MAXX SST® Soft Start Technology® Black & Decker’s Soft Start Technology gradually “ramps up” the inverters power to slowly start appliances that requirea surge to get started. This gradual ramp up protects the inverter and the appliance, as well as the power source, from damage and failure. OPERATING INSTRUCTIONS The Power/Fault LED Indicator lights green when the Inverter is properly connected to a functioning DC power source. The AC and USB outlets are ready to use. (If the Power/Fault LED Indicator lights red, refer to theTroubleshooting Section of this Instruction Manual.) To turn the unit off, disconnect it from the 12 volt DC power source. Always connect the inverter to the 12 volt DC power source before plugging any devices into the unit. The standard North American 115 volt AC and USB outlets allow simultaneous operation of multiple devices. Simplyplug the equipment into the unit and operate normally. Ensure that the wattage of all equipment simultaneouslyplugged into the inverter does not exceed 100 watts continuous. Rated Versus Actual Current Draw of EquipmentMost electrical tools, appliances, electronic devices and audio/visual equipment have labels that indicate the powerconsumption in amps or watts. Be sure that the power consumption of the item to be operated is below 100 watts. Ifthe power consumption is rated in amps AC, simply multiply by the AC volts (115) to determine the wattage. Resistive loads are the easiest for the inverter to run; however, it will not run larger resistive loads (such as electricstoves and heaters), which require far more wattage than the inverter can deliver. Inductive loads (such as TVs andstereos) require more current to operate than do resistive loads of the same wattage rating. For safety reasons, the unit will simply shut down if it is overloaded. To restart the unit, simply remove the load, wait a few minutes, then plug it back in, rotating slightly to make sure there is good contact. Operation of the 115 Volt AC Outlet 1. Connect the unit to a vehicle’s accessory outlet or other 12 volt DC power source. Make sure there is adequatespace for proper ventilation of the inverter. 2. Rotate the unit slightly to make sure there is good contact. 3. The Power/Fault LED Indicator will light green, indicating a proper connection. If the Power/Fault LED Indicatorlights red, a Fault condition exists. Refer to the Troubleshooting Section of this Instruction Manual. 4. If the Inverter does not work, make sure the ignition/accessory outlet is powering the accessory outlet. Some vehicles require the ignition switch to be turned on. 5. Plug the (110/120 volt AC) appliance into the Inverter’s three-prong AC outlet and operate normally. Notes:The Inverter will not operate appliances and equipment that generate heat, such as hair dryers, electric blankets, microwave ovens and toasters. Remember to disconnect the unit from any power source when it is not in use. Operation of the USB Charging Port 1. Connect the unit to a vehicle’s accessory outlet or other 12 volt DC power source. Make sure there is adequatespace for proper ventilation of the inverter. 2. Rotate the unit slightly to make sure there is good contact. 3. The Power/Fault LED Indicator will light green, indicating a proper connection. If the Power/Fault LED Indicatorlights red, a Fault condition exists. Refer to the Troubleshooting Section of this Instruction Manual. 4. If the Inverter does not work, make sure the ignition/accessory outlet is powering the accessory outlet. Somevehicles require the ignition switch to be turned on. 5. Plug the USB-powered device into the inverter’s USB Charging Port and operate normally. Notes:This inverter’s USB Charging Port does not support data communication. It only provides 5 volts DC/500 mA(5 volts DC/200 mA when combined with inverter AC output over 90W) power to an external USB-powereddevice. Remember to disconnect the unit from any power source when it is not in use. Protective Features The inverter monitors the following conditions: Low Battery Voltage —This condition is not harmful to the inverter, but could damage the power source, so theinverter will automatically shut down when input voltage drops below 10.5 ± 0.3 volts DC. Once the voltage recoversthe inverter will auto restart. Input Voltage Too High —The inverter will automatically shut down when DC input volta...
Este manual também é adequado para os modelos :Jig Saw e - PI101B (194.87 kb)