Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
In the event of a power failure, move the switch injury. 10. USE THE GUARDS. Check to see that all guards are in place, secured, and 11. REMOVE ADJUSTING KEYS AND WRENCHES BEFORE THE MACHINE. Tools, scrap pieces, and other debris can be thrown at high speed, causing injury. 12. USE THE RIGHT MACHINE. Don’t force a machine or an attachment to do a the machine and/or injury may result. 13. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not may cause damage to the machine or injury 14. USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good cord, be sure to use one heavy enough An undersized cord will cause a drop line voltage, resulting in loss of power and overheating. See the Extension Cord Chart for the correct 5 the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge the heavier the cord. 15. SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury. 16. FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at a high speed. 17. DON’T FORCE THE WORKPIECE ON THE MACHINE. Damage to the machine and/or injury may result. 18. DON’T OVERREACH. Loss of balance can make you fall into a working machine, causing injury. 19. NEVER STAND ON THE MACHINE. Injury could occur if the tool tips, or if you accidentally contact the cutting tool. 20. NEVER LEAVE THE MACHINE RUNNING UNATTENDED. TURN THE POWER OFF. Don’t leave the machine until it comes to a complete stop. A child or visitor could be injured. 21. TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE before installing or removing accessories, before adjusting or changing set-ups, or when making injury. 22. MAKE YOUR WORKSHOP CHILDPROOF WITH PADLOCKS, MASTER SWITCHES, OR BY REMOVING STARTER KEYS. The accidental start-up of a machine by a child or visitor could cause 23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE. DO NOT USE YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS, A moment of inattention while operating power tools may result in injury. 24. THE DUST GENERATED by certain woods and wood products can be injurious to your machinery in well-ventilated areas, and provide for proper possible. 6 ADDITIONAL SAFETY RULES FOR THE LASER For your convenience and safety the FOR LASER SAFETY OBSERVE THE FOLLOWING CAUTIONS: following labels are on your tool. Fig. B Properly secure cover. Tighten screw before use. Sujete correctamente la tapa. Ajuste el tornillo antes de usar la herramienta. Fixer solidement et correctement le couvercle. Serrer la vis avant utilisation. CLASS 2 LASER RADIATION WHEN OPEN DO NOT STARE INTO THE BEAM. L. SER CLASE 2 EMITE RADIACI” N CUANDO EST. ABIERTO. NO FIJE LA VISTA EN EL HAZ. MISE EN GARDE : RAYONNEMENT LASER CLASSE 2 UNE FOIS L'OUTIL ALLUM…, NE PAS FIXER DU REGARD LE FAISCEAU. LASER RADIATION DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT PER EN60825-1:11994+AII+A2 Pmax-1.0mW, =633-670nm CAUTION/ATENCI” N/ATTENTION RADIACI” N L. SER. NO MIRE FIJAMENTE HACIA EL RAYO. PRODUCTO L. SER DE CLASE 2. RAYONNEMENT LASER. NE PAS FIXER LE FAISCEAU DU REGARD. PRODUIT LASER DE CLASSE 2. COMPLIES WITH 21CFR PARTS 1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO.50, DATED JULY 26,2001. CUMPLE CON LAS NORMAS DEL C” DIGO DE REGULACIONES FEDERALES 21CFR 1040.10 Y 1040.11, CON LA EXCEPCI” N DE LOS APARTADOS CONFORMES AL AVISO L. SER N. 50, DE FECHA 26 DE JULIO DE 2001. CONFORME AUX SECTIONS 1040.10 ET 1040.11 DU CHAP. 21 DU CFR HORMIS LES D… ROGATIONS CONFORM… MENT . LiAVIS N. 50 SUR LE LASER, DAT… DU 26 JUILLET 2001. WARNING AVERTISSEMENT ADVERTENCIA AVOID EXPOSURE: Laser radiation is emited from this aperture. EVITE LA EXPOSICI”N: Por esta abertura se emite radiaciUn l·ser. …VITEZ TOUTE EXPOSITION: Rayonnement laser Emis de cette ouverture. • LASER LIGHT - DO NOT STARE INTO BEAM, APERTURE, or into a reflection from a mirror-like surface Fig. A & B. • AVOID EXPOSURE - LASER LIGHT IS EMITTED FROM FRONT GUARD APERTURE. Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous laser light exposure. • DO NOT DISASSEMBLE LASER MODULE. The laser is a CLASS II LASER PRODUCT that can emit laser power up to 1 mW MAX at 650 nm, which could result in exposure with the module disassembled. The laser unit complies with 21 CFR 1040.10 and 1040.11. • USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. • THE USE OF OPTICAL INSTRUMENTS with this product will increase eyehazard. • LASER RADIATION, avoid direct eye exposure, serious eye injury can result. • DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES, such as in the presence of flammable liquids, gases, or dust. • USE ONLY WITH THE SPECIFICALLY DESIGNATED BATTERIES....