Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
The further apart the tips are, the greater the set. TABLE INSERT – Insert that is removed from the table to install / remove blades. It is also removed for dado cutting. When dado cutting, a dado insert plate must be used. THROUGH SAWING – Making a cut completely through the length or width of a workpiece. WORKPIECE – Material to be cut. Saw blade path Surface Leading edgeKerf Trailing edge Workpiece 17 1717 ASSEMBLY ASSEMBLE STAND (FIG. A, B, C) 1. Unpack all parts and group by type and size. Refer to the parts list for correct quantities. 2. Attach four hooks (10) to the top corner of the four legs (2) as shown. The hooks (10) are used to hold the dust bag. NOTE: Make sure the hook (10) is securely fastened to the corner of the leg (2). Fig. A 3. Attach one long upper support with 10 bolt (3) and nut (4). NOTE: with support brackets to ensure proper fit. . Do not tighten bolts until stand is properly aligned. . Position all supports to the INSIDE of the leg assembles. 4. Attach short upper supports (6) to other hole of leg (2) using one bolt and nut. label (1) to top of leg (2) using one . Align detents (8) in stand leg 2 10 Fig. B 6 2 3 4 8 1 10 5. Assemble the other upper supports in exactly the same manner. 6. Attach one bottom support (5) to the center of the leg using bolt (3) and nut (4). This completes the front frame section. 7. Assemble rear frame section in exactly the same manner. 8. Join front-bottom and rear-bottom frame assemblies using the bottom support (7), bolts and nuts. Fig. C Front 7 5 1 6 2 ASSEMBLE THE ROLLER WHEEL TO STAND (FIG. D, E) 1. Place stand upside down on level surface or floor. 2. Place bottom support bracket for roller wheel (18) inner of the front leg (2). 3. Insert the bolt (12) through the roller wheel bracket (11), front leg (2), bottom support bracket (18) and nut (13) as shown. Tighten the nut. 4. Attach the roller wheel (14) to roller wheel bracket (11), bolt (15) and lock nut (16) using square neck bolt (15) and lock nut (16) as shown. NOTE: Do not overtighten nut as this will not allow the wheels to turn. 18 1818 Fig. D 16 5. Repeat steps 1-4 for left rear leg (17) and roller wheel assembly. 12 13 14 15 2 11 18 NOTE: The roller wheel assemblies and bottom support bracket (18) can be installed on either the right- hand side or left-hand side. Always install the roller wheel assemblies and the bottom support bracket (18) at the same time. The illustration shows the roller wheels on the left- hand side. Fig. E 17 2 18 Front 6. Carefully set the saw in its upright position on a clean level surface. ASSEMBLE THE FOOT PAD TO STAND (FIG. F) 1. Place all four foot pads (9) ontoeach leg. 2. Place stand on level surface and adjust so all legs are contacting thefloor and are at similar angles to the floor, and detents in stand leg alignwith support brackets, then tightenall bolts. NOTE: Stand should not rock after all bolts are tightend. Fig. F 99 ASSEMBLE TABLE SAW TO STAND USING LEVER LOCK (FIG. G) 1. Attach the locking lever assembly (18) to the top of the leg (2). 2. Lift up the locking lever (19). 3. Thread the two screws (20) into the holes (21) of the locking bracket (24) and stand. NOTE: You may need to loosenthe two short support brackets if the two mounting holes are not lined upcorrectly. Retighten these bolts onceyou have added the lever locks. 4. Attach the lock nuts (22) and tightenwith a 8 mm or adjustable wrench. 5. Install the other locking lever assemblies in exactly the same manner. 6. Position the saw base on the stand. 7. Line up the lever lock cover (23) tothe saw base and push down the locking lever (19). 8. Fasten saw to stand using fourlocking lever assemblies (18). NOTE: The four locking lever assemblies (18) are provided forquick releasing the table saw to thestand. ! WARNING All four levers must be locked in the down position before operating saw. Fig. G 2 20 22 24 18 2319 21 19 1919 MOUNTING BASE TO STAND USING BOLTS (FIG. H) You can also attach the saw base to the stand using standard bolts. 1. Fasten the base to the stand using the four long bolts (25), flat washers (26), and nuts (27). 2. Place a washer on the bolt and insert thru the hole in saw base and slot in stand. Attach the nut and tighten using a 13 mm wrench. Repeat for other three corners. Fig. H 25 25 26 26 27 27 SAW MOUNTED TO WORK SURFACE (FIG. I) 1. If the leg set will not be used, the saw must be properly secured to a sturdy workbench using the four mounting holes at the base of the saw. 2. The surface of the table where the saw is to be mounted must have a hole large enough to facilitate sawdust fall-through and removal. 3. Square the saw on the mounting surface and mark the location of the four 3/8 in. mounting holes (1). 4. Drill 3/8 in. hole into the mounting surface. 5. Mark an 11 in. square (2) centered between the four mounting holes (1). 6. Cut out and remove the square. 7. This opening will allow sawdust to fall through the saw base. 8. Place the saw on the work surf...