Assessments - 6, GPA: 3.8
(
)
)
|
Facilidade de uso
-Crosscuts should be performed only with the help of a mitre fence or the Sliding Carriage PK, available as optional accessory. -Do not crosscut round stock, for ripping use the Square and Round Stock Jig available as optional accessory. -Maximum saw blade diameter is 300 mm, the minimum blade diameter must be 250 mm. User Responsibility This machine will perform in conformity with the description contained tin the instructions provided. This machine must be checked periodically. Defective equipment (including power cable) should not be used. Parts that are broken, missing, plainly worn, distorted or contaminated, should be replaced immediately. Should such repair or replacement become necessary, it is recommended that such repairs are carried out be qualified persons approved by Elektra Beckum or its representative. This machine or any of its parts should not be altered or changed from standard specifications. The user of this machine shall have the sole responsibility for any malfunction which results from improper use or unauthorized modification from standard specification, faulty maintenance, damage or improper repair by anyone other than qualified persons approved by Elektra Beckum or its representative. Product Liability/Warranty We explicitly draw your attention to the fact that, under the current product liability regulations, Elektra Beckum does not have to assume liability for any damages causes by its products, if such damages result from improper repair, use of replacement parts other than genuine Elektra parts, or repairs not having been carried out by customer service or authorized service centres. The three-phase motor of this machine is equipped with an automatically engaging mechanical motor brake, designed for a long service life. If the braking action fades, and the time to standstill exceeds 10 sec, the brake has to be replaced. Consult your dealer or authorized service centre. Table of Contents 1 Specifications 10 Dust Collection 2 Standard Delivery 11 Operation 3 Installation 12 Adjusting the Saw Blade Position 4 Connection to Power Mains 13 Belt Tension 5 Controls/Settings 14 Care and Maintenance 6 Saw Blades 15 Wiring Diagrams 7 Overview of Components/Terms 16 Optional Accessories 8 Jigs and Push Blocks 17 Spare Parts Lists 9 Safety Rules Specifications PK 300 K/4200 DNB Saw table size 710x900 mm Table working height 940 mm Dept of cut at 90°/45° 104/70 mm Motor speed 2800 rpm Arbor speed 3800 rpm Main blade diameter 300 mm Cutting speed with O 300 mm blade 60 mtr/sec Motor capacity P1 4200 W- Motor voltage 3 ~ 400 V Mains frequency 50/60 Hz Mains fuse 3 x 16 A time-lag Suction port diameter 100 mm Weight 90 kg Stock-no. 010 300 4209 Noise Emission The noise emission levels shown below have been established by measuring methods according to: DIN EN 23 746; DIN EN 31 202; ISO 7960 appendix A. The correction factor K3 has been established by DIN EN 31204. 1. PK 300 K operating under no load A-sound pressure level LpA 74,3 dB(A) A-sound power level LWA 87,8 dB(A) 2. PK 300 K operating under load A-sound pressure level LpA 84,7 dB(A) A-sound power level LWA 98,2 dB(A) 16 Standard Delivery Saw blade TCT 300x2.6/1.8x30 mm 28 alternate bevel teeth Riving knife 2.5 mm Saw blade guard Rip fence Mitre fence Dust extraction port with hoses Push stick Tool set Operating instructions Installation Place machine upside down on two battens to install the workstand. Do not tighten screws fully before all parts have been installed. Install suction port to chip case. Use 3 each hex. head screw M 6x16 serrated lock washer O 6.4 hex. nut M 6 Place spiral hose O 100 mm onto suction port and secure with hose clamp O 100 mm. Install both side panels, using 4 each hex. head screw M 6x16 serrated lock washer O 6.4 hex. nut M 6 Install rear panel (with hole) between the side panels. Use 6 each hex. head screw M 6x16 serrated lock washer O 6.4 hex. nut M 6 Install dust collection port into hole of the rear panel with 3 each hex. head screw M 6x16 serrated lock washer O 6.4 hex. nut M 6 Place the spiral hose on the dust collec- tion port and secure in place with the second hose clamp O 100 mm. Install the workstand's front panel. Use 6 each hex. head screw M 6x16 serrated lock washer O 6.4 hex. nut M 6 Put a hex. nut M 10 on the threaded bolt of all 4 adjustable feet. Install feet into tapped bushes M 10 lo- cated on each corner. Now tighten all screw joints fully, then stand machine on its feet. Place side panels lids into the panel openings. 17 Loosely attach 2 carriage bolts M 6x16 to hose carrier, then slide hose carrier into the Raise saw blade (see paragraph 5) and rear T-groove of the table. attach saw blade guard to riving knife. Install spiral hose between saw blade guard and dust collection port. 3.1 Rip Fence Scale Adjustment The rip fence scale is adjustable to accommodate saw blades of different widths. Set rip fence against the blade. Loosen scale fixing screw and set scale until zero mark matches...