Log:
Downloads : 4   Arquivo Tamanho: 20 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name

If an adapter is used to accommodate a two-prong receptacle, the adapter wire must be attached to a known .pound. Never remove the third prong. 4. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to ж that keys and adjusting wrenches are removed before turning on tool. 5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 6. AVOID DANGEROUS ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp or wet locations. Keep your work area well Illumi

Downloads : 1   Arquivo Tamanho: 20 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name

If the end of the rod strikes the table do not change the height adjustment of the saw. Instead, lower the front right side of the table by turning the upper nut on the suspension stud up a few turns. You should now be able to push the front right corner of the table down so the rod indicator can pass over the surface without striking it. 7. Adjust the suspension stud nuts so the top of the table on the front right side just touches the end of the antikickback rod the same as the back. Tighten

Downloads : 0   Arquivo Tamanho: 20 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name

Replace cover by lining up holes in cover with holes in the raised sections of the ball retainer assembly. Replace screws and tighten securely (Fig. A13). Fig. A13 2. YOKE CLAMP HANDLE The purpose of this handle is to provide a friction lock between the -upper face of the yoke and the bottom face of the rollerhead. It should also eliminate any play between these two ■ parts. To lock, the handle is 'pushed back from the hand grip of the yoke. If at any time if is possible to move this handle s

Downloads : 4   Arquivo Tamanho: 20 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name

Turn the motor “OFF”. Figure K5C Moving the saw back through lb« trough and 1/4-circle kerfs, bring the saw again to the position at the-end of the arm as shown in Figure K5. Tighten Rip Lock and release Yoke Clamp Handle. Turn -motor “ON" and temporarily press the Yoke Locator Pin Handle as you start to rotate the yoke counterclockwise (Figure K5D). Continue rotating until the Locator. Pin stops the yoke, after a 1/4-circie cut, with the blade parallel to the fence. Now, with the motor still

Downloads : 8   Arquivo Tamanho: 20 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name

REVIEW SAFETY RULES AND OPERATING INSTRUCTIONS FREQUENTLY. This booklet is provided for your convenience: iw the use ami care of your new DeWalt Saw. These instructions include operation, usage, precautions^ preventive maintenance, maintenance and other pertinent data to assist you in assuring long; life and dependable service from your saw. 700 8" RADIAL ARM SAW No. 7700/3400,120 VOLT, TYPE 5 No. 7700-01,220 VOLT, TYPE 5 Bulletin No. 8814 - INDEX Unpacking, Set-Up..............2-4 Macfii

Downloads : 1   Arquivo Tamanho: 20 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name

Set and test the anti-kickback device the same as in RIPPING even though only one of the fingers will take the main “bite”, if needed.-Remember to raise the front, lower blade guard to clear rip fence if needed. Figure §13 20 DADO & PLOUGH CUTS (CUTTING GROOVES) Figure S14 A “Dado” is a grmm mmm the wood grain Ccrosscut) (figure S14). A “Plough" is a groove with the wood grain (rip) (Figure $15). These cuts can be made to any width with a regular saw blade by miking one cut next to another

Downloads : 10   Arquivo Tamanho: 6 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name@name@name

Questions? See us on the World Wide Web at INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. See the Quick Start Guide on page 4! Se reporter en page 17 du Guide de demarrage ! .Vea la Guia de referencia rapida en la pagina 31! D24000 Wet Tile Saw Coupe-tuile a l’eau D24000 Sierra de corte humedo D24000 English IF YOU HAVE ANY QUESTIONS ABOUT THIS OR ANY

Downloads : 1   Arquivo Tamanho: 4 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name@name@name

4. The third hole is at the rear of the machine. An alternate method of securing the scroll saw to a supporting surface is to fasten the scroll saw to a mounting board. Then securely clamp the mounting board to a stand or workbench using two or more C-clamps. NOTE: For proper stability, the holes in the mounting board must be countersunk at the bottom so that the fastener heads are flush with the bottom surface of the mounting board. Fig. 4 A OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS STARTI

Downloads : 5   Arquivo Tamanho: 2 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name@name@name

386782-01 DW705 Copyright 2001, 2002 Before returning call 1-800-4-DEWALT IF YOU SHOULD PURCHASE, CALL 1-800- IN MOST CASES, REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER IF YOU HAVE A SUGGESTION OR GIVE US A CALL. YOUR FEEDBACK IS VITAL TO THE SUCCESS OF DEWALT'S QUALITY IMPROVEMENT INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO INSTRUCTION MANUAL ANTES DE USAR EL PRODUCTO. GUIDE D.UTILISATION MANUAL DE INSTRUCCIONES DW705 (120 Volt)/DW705 (220 Vol

Downloads : 4   Arquivo Tamanho: 2 mb   Fabricante : DeWalt  
Categoria : Jig Saw e
@name@name@name

36-714 36-714 10" Hybrid Saw Scie hybride de 254 mm (10 po) Sierra combinada de 254 mm (10'') Instruction Manual Manuel d’Utilisation Manual de Instrucciones FRANCAIS (27) ESPANOL (53) (800) 223-7278 - US (800) 463-3582 - CANADA A19706_10-05-06 Copyright © 2006 Delta Machinery TABLE OF CONTENTS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ....................2 SAFETY GUIDELINES - DEFINITIONS .....................2 GENERAL SAFETY RULES .......................................3 ADDITIONAL SPECIF





categorias