Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
92. OPERATION R Type (remote control) For panel mount or top mount remote control information, refer to the instructions provided with the remote control equipment. Side-Mount Type SWITCH CLIP LANYARD 1. Put the emergency stop switch clip in the emergency stop switch, and attach the lanyard to your PFD (Personal Flotation Device) or to your wrist, as shown. The engine will not start or run, unless the switch clip is in the emergency stop switch. The emergency stop switch clip and lanyard system is a safety device that will stop the engine if you fall away from the controls while operating the boat. Always attach the lanyard to your PFD, or to your wrist, before starting the engine. N(neutral) 2. CONTROL LEVER Set the control lever in the N (neutral) position. The engine will not start if the F (forward) or R (reverse) gears are engaged. OPERATION FAST IDLE FAST IDLE LEVER 3. To start a cold engine, leave the fast idle lever in the OFF (fully lowered) position. To restart a warm engine, raise the fast idle lever. Fast idle lever cannot be raised unless the control lever is in the N (neutral) position. The control lever cannot be moved away from the N (neutral) position unless the fast idle lever is lowered. ON START OFF IGNITION SWITCH KEY 4. Turn the ignition switch key to the START position and hold it there until the engine starts. When the engine starts, release the key, allowing it to return to the ON position. If the engine fails to start within 5 seconds, release the key and wait at least 10 seconds before operating the starter again. Using the electric starter f or more than 5 seconds at a time will overheat the starter motor and can damage it. Turning the ignition switch key to the START position while the engine is running can damage the starter motor and f lywheel. OPERATION FAST IDLE LEVER 5. If the fast idle lever was used to start the engine, gradually lower the lever as the engine warms up. When the fast idle lever is fully lowered, the control lever can be moved away from the N (neutral) position. 6. Before getting under way, allow the engine to warm up sufficiently to ensure good performance. Above 41°F (5°C), warm up the engine for 2 or 3 minutes. Below 41°F (5°C), warm up the engine for at least 10 minutes at 2,000 rpm. During the warm-up period, check the oil pressure indicator (p. 30 ), overheat indicator (p. 30 ), and cooling system indicator (p. 31 ). If the indicators show any abnormal condition, immediately stop the engine and determine the cause of the problem. Refer to TAKING CARE OF UNEXPECTED PROBLEMS fromp. 92. EMERGENCY STARTING If the battery is discharged, or the starter motor and the recoil starter are inoperative, you can start the engine manually using the emergency starter rope supplied with the motor. UNLATCH ENGINE COVER LATCH 1. Unlatch and remove the engine cover (p. 69 ). - 50 OPERATION RECOIL STARTER ASSEMBLY FLYWHEEL (STARTER PULLEY) KNOT RECOIL STARTER ASSEMBLY NEUTRAL START CABLE STARTER ROPE FLANGE BOLT TAKING CARE OF Set the knotted end of the UNEXPECTED PROBLEMS, emergency starter rope in the notch in the flywheel. Wind the rope clockwise around the flywheel, as shown. Set the controls the same as for normal starting (see pages ). Use the choke and fast idle controls if needed. Turn the ignition switch key to the ON position. Unscrew the three flange bolts and remove the recoil starter assembly. Move the shift lever to the F (forward) position. Loosen the neutral start cable lock nut and disconnect the neutral start cable. Pull the emergency starter rope slowly until resistance is felt, then pull briskly. Keep away from moving parts while pulling the rope. If necessary, rewind the rope and pull again. If the engine does not start after several attempts, refer to p. . 2. 3. 5. 4. 6. 44 49 92 N 7. If the choke and fast idle control(s) was used to start the engine, return the control(s) to the normal operating position as the engine warms up. During the warm-up period, check the oil pressure indicator (p. 30 ), overheat indicator (p. 30 ), and cooling system indicator (p. 31 ). 8. Leave the recoil starter assembly off, but install the engine cover (p. 27 ), and lock it in place by latching the engine cover latch. Exposed moving parts can cause injury. Do not operate the outboard motor without the engine cover. Use extreme care when installing the engine cover. 9. If it was necessary to remove the emergency stop switch lanyard from your wrist to perform the emergency starting procedure, be sure the lanyard is attached to your wrist before operating the outboard motor. 10. Have your closest authorized Honda marine dealer check your electrical system and correct the problem, so you can use the electric starter. The recoil starter assembly (p. 50 ) should be reinstalled after the electric starter is working again. Install the recoil starter assembly with the engine stopped. 52 STOPPING THE ENGINE Normal Engine Stopping Emergency Engine Stopping OPERATION SWITCH CLIP ...
Este manual também é adequado para os modelos :Barcos - BF15D (4.42 mb)
Barcos - BF20D (4.42 mb)
Barcos - BF8D (4.42 mb)
Barcos - BFP15D (4.42 mb)