Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
A small "A" or "P" will be to the lower left of the hours to denote AM or PM. New Settings Date Settings When setting the date the year is also displayed. Press MODE button until Time Mode is displayed. Press and hold down ADJ for 3 seconds. Press MODE button and scroll to desired setting to change. Press UP or DOWN button until desired value appears, and then press MODE button for next setting. Press ADJ button at any time to save changes and exit. For 24/12 hour setting press MODE button until Time Mode is displayed. Press and hold down ADJ for 3 seconds. Press MODE button and scroll through settings until 24/12 hour setting appears, then press UP or DOWN button to enter desired setting. Press ADJ button at any time to save changes and exit. TEMPERATURE Temperature Mode Press MODE/NEXT button until Time Mode is displayed. If already in Time Mode then just press MODE/NEXT button and Temperature Mode is displayed. Press UP or DOWN button to toggle between Celsius and Fahrenheit readings. ALARM Alarm Setting Mode Press MODE button until Alarm Mode is displayed. The alarm consists of 5 alarms, 4 for Time and 1 for Temperature. Press UP or DOWN button to scroll through the different alarms. Press and hold down ADJ for 3 seconds until the minute blinks, press UP or DOWN button to adjust to desired values. Press MODE button for next setting. Press ADJ button at any time to save changes and exit. The alarm is activated automatically after adjustments have been made. To stop the alarm from beeping, press any button. The alarm can also be turned on or off by going to the relevant alarm and pressing the COMP button to activate alarm function, press again to activate Snooze function, and press again to de-activate alarm. 4 5 Temperature Alarm Sets the alarm to sound when the temperature measurement reaches the programmed level. In the Alarm Mode, the Temperature alarm uses the same measurement units (.C or F) that were last set in the Temperature Mode. To change this you must first change the temperature units in the Temperature Mode. Using the UP/DOWN once changes the temperature in tenths of a degree. Holding the button down changes the temperature in increments of 1 degree. Beep Function In the Alarm mode a Beep function is also available. When activated, the beep function causes a beep sound to be made whenever a button is depressed, even when the Alarm function is turned off. To activate the function go to the Beep function in the Alarm Mode, press the COMP button and ‘ON’ is displayed. Press again and ‘OFF’ is displayed. Stopwatch Mode Press MODE button until Stop Watch Mode is displayed. To operate, press UP button to start and press again to stop. Pressing DOWN button will reset the Stop Watch. For split timing function, press the DOWN button while the Stop Watch is operating in order to stop the display and press again to continue. You can also press the DOWN button while the Stop Watch is operating to stop the display and then press the UP button to stop the Stop Watch and display the final reading. Press the DOWN button again to reset the Stop Watch. Stop Watch Mode / Split Timing Function Split timing function is displayed as ‘SPL’ when activated and the display returns to normal when DOWN button is pressed. COUNTDOWN TIMER ALARM Countdown / Reverse-Timer Mode Press MODE button until Countdown Timer Mode is displayed, represented by ‘RT’ (reverse timer). To operate press UP button to start and press again to stop, then press DOWN button to reset the Countdown Timer. To set the Countdown Timer press and hold down ADJ button for 3 seconds, which will cause the seconds setting to blink. Adjust with the UP or DOWN button, and then press MODE button to adjust next setting. Press ADJ button to save settings and exit. Press COMP for ‘AUTO’ to allow Countdown Timer to repeat function automatically, and press COMP again to turn off ‘AUTO’ function. Press any button when alarm sounds to stop the Countdown Timer. If nothing is pressed the Countdown Timer will stop beeping after 10 seconds, but it will continue if the ‘AUTO’ function is set on. To stop the Countdown Timer if the ‘Auto’ function is on, you must go to the Countdown Timer Mode and press COMP to turn off the ‘Auto’ function and then press UP button to stop it. DIGITAL COMPASS Compass Mode Press MODE button until Time Mode is displayed, and then press COMP button. If already in Time Mode, simply press COMP button and Compass Mode is displayed. Hold the compass level using the bubble level to get a reading. If the Cardinal Points blink then the compass probably needs to be calibrated. (See trouble shooting tips.) Compass Calibration In Compass Mode, hold down ADJ button for 3 seconds. Calibration Mode is displayed. Put the compass on a level, nonmagnetic surface and press the COMP button. The word CAL will start blinking. Then, rotate the compass 2 full circles slowly WHILE HOLDING THE COMPASS LEVEL. When done, press COMP again. When completed, the display...