Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
1 nautical mile visibility. CAUTION Read all instructions carefully before installing and using this product. All positive (+12V DC) lighting wires require a 1-amp fuse to protect circuits and vessel. The aluminum light pole is not grounded. MAKE SURE POWER SOURCE IS 12-VOLT DC ONLY. HIGHER VOLTAGE WILL DAMAGE LIGHT AND CIRCUITRY. WARNING Disconnect power when installing or servicing this product. Remove boat from water before using any 120V AC power tools. LOCATION Lights must be mounted to an unobstructed smooth surface on the gunwale, deck or superstructure. Locate Bi-Color Combination Light in an area as far forward as possible. (Figure 1) INSTALLATION Bases That Do Not Use Locking Collars 1. Align pole screw with the slot (or locking spring) in the existing base. Insert pole into base (Figure 2). 2. Press down fi rmly to engage electrical connectors. With Easy Lock Base, be sure locking spring clicks over pole screw. 3. To remove: • Pull locking spring back (on Easy Lock Base) • Pull pole straight up. Bases That Use Locking Collars 1. Align pole screw with the slot (or locking spring) in the existing base. Insert pole into base (Figure 3). 2. Press down fi rmly to engage electrical connectors. With Easy Lock Base, be sure locking spring clicks over pole screw. 3. Slide locking collar down to base, rotate until you can insert lower ring inside top of base. NOTE: Locking Collar stays above the Easy Lock Base 4. On bases other than the Easy Lock Series, press collar down into base and rotate until it tightens between pole and base. NOTE: Periodically check pole to make sure it is secure. 5. To remove: • Pull locking spring back (on Easy Lock Base) • On other bases, rotate locking collar in opposite direction until it loosens, • Pull pole straight up. TO CONVERT POLE FOR USE WITHOUT LOCKING COLLAR 1. For bases that do not accept locking collar, remove screw at bottom of pole. Slide locking collar off end of pole. 2. Replace screw in the upper screw hole. OPERATION After installation, check lights to verify proper operation. Regulations require lights to be operated with a three-position switch for: 1. Running lights (bow lights and all-round light); 2. Anchor lights (all-round light only); 3. Off. BASE WIRING IMPORTANT: LED-based lights MUST be wired for correct polarity (Figure 4). If your light function after installation, the light base may require re-wiring. To re-wire if necessary: 1. Unscrew or remove the base so you can reach wiring. 2. Locate the connection between base wiring and the boat’s wiring harness. 3. Cut wires. Add waterproof splice to each wire end. 4. Reverse polarity by reversing original wire connection to the 5. Temporarily plug light into the base to check operation. 6. Remove light and reinstall base. NOTE: Do not use light pole as a fl agpole or handle. MAINTENANCE When not in use, store in Pole Light Storage where light will not be damaged or be in ATTWOOD LIMITED 10- Because of the longevity LED lighting technology, Attwood offers a limited warranty on this LED lighting © 2008 Attwood 1016 N. Monroe Figure 1 / Figura 1 AB Abbildung 1 / Figur 1 Figure 1 Figure 1 A. Red A. Rouge B. Green B. Vert Figura 1 Abbildung 1 A. Rojo A. Rot B. Verde B. Grun Figur 1 A. Rod B. Gron Figure 2 / Figura 2 Abbildung 2 / Figur 2 B A • Figure 3 / Figura 3 Abbildung 3 / Figur 3 A • B • C • D E Figure 3 A. Locking Collar B. Lower Ring C. Screw D. #91020, #91024 or #91026 E. #91022 Figura 3 A. Collarin de seguridad B. Anillo inferior C. Tornillo D. Numeros 91020, 91024 o 91026 E. Numero 91022 Figur 3 A. Laskrage B. Undre ring C. Skruv D. #91020, #91024 eller #91026 E. #91022 Figure 4 / Figura 4 Abbildung 4 / Figur 4 Figure 3 A. Bague de blocage B. Bague inferieure C. Vis D. N° 91020 91024 ou 91026 E. N° 91022 Abbildung 3 A. Verriegelungszylinder B. Unterer Ring C. Schraube D. Nr. 91020, Nr. 91024 oder Nr. 91026 E. Nr. 91022 Figure 2 A. Pole Screw B. Locking Spring C. EASY LOCK BASE Figura 2 A. Tornillo del asta B. Resorte de seguridad C. BASE DE AJUSTE FACIL Figur 2 A. Stangskruv B. Lasfjader C. EASY LOCK BASE C Figure 2 A. Vis du mat B. Ressort de verrouillage C. BASE FACILE A BLOQUER Abbildung 2 ...