Assessments - , GPA: ( )

Instruções de Operação Attwood, Modelo 5045

Fabricante : Attwood
Arquivo Tamanho: 480.46 kb
Arquivo Nome : 69379-b-pulsar-lights.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

12-Volt Navigation Lights All-Round Lights: 5940, 5980 Sidelights: 5040, 5045, 5080 Installation Instructions SAVE THESE INSTRUCTIONS Form Number 69379 Rev. B 03-10 FEATURES The Attwood Pulsar Navigation Lights are designed for boats upto 39.6 ft. (12 meters). They feature impact resistant, UV-stable polycarbonate housings. The lens completely encloses the bulb and socket for a splash resistant seal. Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all applicable standards as tested by Imanna Labs, March 1997. 5040, 5045, and 5080 are Sidelights with 1 Nautical Mile visibility. 5940 and 5980 are All-Round Lights with 2 Nautical Mile visibility. All use Lamp 9235, #906, 13V, 6 Candle Power. REQUIRED FOR INSTALLATION • Cordless drill with 1/8", 3/8", and 3/4" (3, 10, and 19mm) bits. • Screwdriver. • Two #8 or #10 stainless pan head screws per light. • Non-silicone sealant. WARNING: To prevent personal injury, disconnect the power source when installing or servicing this product. Always remove the boat from the water before using 120V AC power tools. LOCATION (All-Round Lights) All-Round Lights must be mounted a minimum of 1 meter above the sidelights, on a smooth surface where the 360° beam will not be obstructed. Light must not shine on operator or on anything in operator’s field of view. (Figure 1) Important: Before drilling mounting holes, be sure that light shines within 5° of horizontal when the boat is floating. Figure 1 One meter or 39-3/8" LOCATION (Sidelights) Mount sidelights to a smooth surface on the gunwale, deck or superstructure where the light beam will not be obstructed. Position Bi- Color combination light as far forward as possible. (Figure 2) Important: Before drilling mounting holes, be sure sidelights shine straight ahead and that they shine within 5° of horizontal when the boat is floating. Figure 2 Red Green Red Green (Port) (Starboard) (Port) (Starboard) 2. Place light in position as shown in Figure 1. Important: Before drilling, be sure that light will shine within 5° of horizontal when boat is floating. 3. Mark and drill 3/4" (19mm) diameter hole. (Figure 3) 4. Thread wire leads and base stem into hole. Mark location of screw holes. Proceed to Step 5 below. Bi-Color Sidelights and Sidelight Pairs 1. To access mounting holes, gently twist lens helmet counterclockwise to remove. 2. Place sidelight(s) in position as shown in Figure 2. Important: Before drilling, be sure that sidelights will shine straight ahead and within 5° of horizontal when boat is floating. 3. For Bi-Color Combination light, mark and drill a 3/4" (19mm) diameter hole on the boat centerline. For Sidelight Pairs, mark and drill a 3/4" (19mm) diameter hole on each side deck of the boat, equal distance from the bow. (Figure 3) 4. Thread wire leads and base stem into hole. Align centerline mark with straight-ahead position and mark location of screw holes. 5. Remove base and drill 1/8" (3mm) pilot holes for both screws. 6. Bring 12V DC (+) and (-) wi...