Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
not extend to any batteries or fuses used with the pump. This limited warranty is not applicable if the pump has been damaged by accident, improper installation, unreasonable use, lack of proper maintenance, unauthorized repairs or modifications, or other causes not arising out of defects in materials and workmanship. 3. Wire strippers. 4. Four (4) wire connectors or equivalent. POTABLE WATER PUMP 5. One (1) in-line fuse holder with 2 amp fuse. Attwood’s obligations under this warranty are limited to repair of the product at Attwood’s plant or replacement of the product at Attwood’s option and at Attwood’s expense. Any expenses involved in the removal, 6. Two (2) #10 panhead screws (length must not protrude through deck). FIGURE 1 reinstallation, or transportation of the product are not covered by this BROWNTO BATTERY TO POTABLE WATER PUMP FIGURE 2 Potable Water Pump Mounting Instructions SAVE THESE INSTRUCTIONS Form Number 69239 Rev. B 03-11 FEATURES: The Potable Water Pump is a rugged, small sized fresh water pump used to deliver water to a faucet. Ideal for use with the Attwood 6142 Faucet/Hand Pump. It is made of ABS non-corrosive FDA approved plastic. Meets U.S. Coast Guard Safety Standards Sections 33 CFR 183.410 and 183.425. Listed by the International Association of Plumbing and Mechanical Officials (IAPMO). Attwood marine hardware, navigation lighting, interior lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s best-known boat manufacturers as original equipment. Look to Attwood for quality replacement parts and add-on marine accessories. CAUTION: The Potable Water Pump is designed to pump fresh, potable water only. It must not be used to pump gasoline or other flammable liquids. TOOLS AND MATERIALS REQUIRED: 1. Drill and suitable drill bits. 2. After installing the pump, connect the pump’s black lead wire directly to the 12 volt battery negative (-) connector. Connect the pump’s brown wire lead to one wire of an in-line fuse holder and connect the other fuse holder wire to one lead wire from the Electric Faucet. Connect the other Electric Faucet lead wire directly to the 12 volt battery positive (+) connector. (See Figure 1). Added wire must be 18 gauge or larger. An optional power ON/OFF switch, such as Attwood 7589 or 7563, may be installed as a master switch as shown in Figure 2. The pump may be threaded directly into the tank. However, this is a centrifugal pump and must be positioned lower than the source of water to operate. Do not install on a surface higher than the bottom of your fresh water supply tank. NOTE: When installing, outlet nozzle should always be higher than inlet nozzle. (See Figure 3) WIRE CONNECTORS BROWN BLACK CITY WATER CONNECTION Attwood 6142 3-WAY ELECTRIC FAUCET CHECK TEE VALVE WIRE CONNECTORS 12 VOLT BATTERY WATER SUPPLY TANK FUSE AND HOLDER BROWN BLACK Attwood 6126 30-40 PSI PRESSURE LIMITING VALVE INCORRECT CORRECT OUTLET ABOVE INLET INLET INLET OUTLET BELOW INLET FIGURE 3 CAUTION: This product is not water resistant and must be installed in a dry location. Do not use synthetic rubber sealant (Silicone, RTV, etc.) or any sealant which smells like vinegar to seal the pump or its fittings. Use of these materials may cause the pump to crack. It is best to use plumbers Teflon® tape where required. CAUTION: ALWAYS protect the pump and the wiring with a 2 amp fuse. For 12 volt DC use only. ATTWOOD LIMITED WARRANTY BILGE PUMPS ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331, (“Attwood”) warrants to the original consumer purchaser that this Attwood Potable Water Pump will be free from defects in materials and workmanship under normal use and service for a period of one (1) year from the date of original consumer purchase. This warranty does 7. Suitable length of 3/8" I.D. hose for pump to tank and pump to faucet. 8. Four (4) stainless steel screw-adjustable hose clamps. 9. Additional wire, if needed, in 16 or 18 gauge size. INSTALLATION INSTRUCTIONS: 1. Select a suitable location for this pump, keeping in mind that it must be a dry area. The pump has intake and outlet fittings to fit 3/8" I.D. soft plastic tubing or 1/4" female pipe thread (cut off hose barb if necessary). Teflon® plumbers tape must be used for all OPTIONAL MASTER SWITCH INSTALLATION BLACK BROWN Attwood 7589 or 7563 SWITCH warranty. The product must be returned to Attwood’s plant at the address indicated above, postage prepaid, with proof of original purchase, including date. If Attwood is unable to replace the product and repair is not commercially practicable or cannot be timely made, or if the original consumer purchaser is willing to accept a refund in lieu of repair of replacement, Attwood may refund the purchase price, less an amount for depreciation. The acceptance by Attwood of any product returned or any refund provided by Attwood shall not be deemed an admission that the product is defective or in violation of any warranty. This w...