Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
. The ambient temperature should be between 41°F and 104°F (5°C and 40°C) while charging is in progress. Charging outside this range may not fully charge the battery. . The battery pack life is over when its operating time decreases even though it is fully and correctly charged. Replace the battery pack. 8 INSTALLING/ REMOVING THE BATTERY PACK . Do not short the battery terminals or dispose of the battery by fire. . Never attempt to remove the casing from the battery pack. 1 Align the battery pack with the back of the transceiver, then press the battery pack and transceiver firmly together until the release latch on the base of the transceiver locks. 2 To remove the battery pack, lift the safety catch on the base of the transceiver, then press the release latch underneath the safety catch. 3 While pressing the release latch, pull the battery pack away from the transceiver. 9 INSTALLING THE ANTENNA Screw the antenna into the connector on the top of the transceiver by Antenna holding the antenna at its base and turning it clockwise until secure. Note: The antenna is neither a handle, a key ring retainer, nor a speaker/ microphone attachment point. Using the antenna in these ways may damage the antenna and degrade your transceiver’s performance. INSTALLING THE BELT CLIP If necessary, attach the belt clip using the two supplied 3 x 8 mm screws. Belt clip Note: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment. Do not use glue which is designed to prevent screw loosening when installing the belt clip, as it may cause damage to the transceiver. Acrylic ester, which is contained in these glues, may crack the transceiver’s back panel. 10 INSTALLING THE COVER OVER THE SPEAKER/ MICROPHONE JACKS If you are not using a speaker/ microphone, install the cover over the speaker/ microphone jacks using the supplied 3 x 6 mm screw. Speaker/ microphone jack cover Note: To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cover. INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET) 1 Insert the speaker/ microphone (or headset) plugs into the speaker/ microphone jacks. 2 Attach the locking bracket using the supplied 3 x 6 mm screw. Speaker/ microphone locking bracket Note: The transceiver is not fully water resistant while using the speaker/ microphone. 11 GETTING ACQUAINTED Antenna LED indicator Lights red while transmitting. Lights green while receiving a signal. Flashes red when the battery voltage is low while transmitting. Speaker Microphone PTT (Push-To- Talk) switch Press, then speak into the microphone to call a station. Release to receive. Side 1 key Press to activate its programmable function (page 13). Side 2 key Press to activate its programmable function (page 13). 12 Channel selector Rotate to select channels 1 ~ 16. Power switch/ Volume control Turn clockwise to switch ON the transceiver. To switch OFF the transceiver, turn counterclockwise until a click sounds. Rotate to adjust the volume level. Speaker/ microphone jacks Battery pack (KNB-45L) PROGRAMMABLE AUXILIARY FUNCTIONS Your dealer can program each of the Side 1 and Side 2 keys with one of the following auxiliary functions. Refer to their descriptions, starting on page 15. • Autodial • Key Lock • Key Lock with Backup • Monitor • Monitor Momentary • None (No function) (default setting for Side 1 key) • Scan • Scan + Temporary Delete • Scrambler • Squelch Off • Squelch Off Momentary (default setting for Side 2 key) • Talk Around • Temporary Delete 13 BASIC OPERATIONS 1 1 Turn the Power switch/ Volume control clockwise to switch the transceiver power ON. • A beep sounds if enabled by your dealer. 2 Press the key programmed with the Monitor or Squelch Off function to hear background noise, then rotate the Power switch/ Volume control to adjust the volume. 3 Rotate the Channel selector to select your desired channel. • When you receive an appropriate signal, you will hear audio from the speaker. 4 To make a call, press and hold the PTT switch, then speak into the microphone using your normal speaking voice. • Hold the microphone approximately 1.5 inches (3 to 4 cm) from your lips. 5 Release the PTT switch to receive. Note: When the battery pack voltage becomes too low, transmission will stop and an alert tone will sound. See “Low Battery Warning” on page 23. 14 ADVANCED OPERATIONS The following functions are programmable by your dealer, as described on page 13. AUTODIAL Press and hold the PTT switch, then press the key programmed as Autodial to transmit the stored DTMF code. Release the Autodial key, then speak into the microphone while still pressing the PTT switch to call the other party. TALK AROUND You may occasionally experience an interruption in service (due to a power failure, etc.). During such an occurrence, you can continue communication by using the Talk Around feature, if it has been programmed by your de...
Este manual também é adequado para os modelos :equipamento de barco - TK-2202L (770.73 kb)