Assessments - , GPA:
(
)
)
Fabricante : Curtis
Arquivo Tamanho: 39.63 kb
Arquivo Nome : e2244204-de45-49c1-b423-52cae6795567.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Amplitude 44-55g, half sine, 9-13 msec duration. 9 Vibration Meets SAE J 1378 March 83. Double amplitude of 1.53 mm with frequency sweep from 10-80-10 Hz (20 g max) at intervals of 1 minute. ! Humidity 95% RH (non-condensing) at +38C Water/dust immunity Face IP63 Rear IP50 Salt spray (fog) ASTM B 117-73 as per SAE J1810, section 4.7.1.2 10 ! 4. INSTALLATION Terminal Assignment for Models 2111R, 2112R, 2113R 1 Sender in 2 Battery + 3 Ground 4 Sender low (optional: for use with two wire senders) 5 Output signal (upper) 6 Output signal (lower) 11 Terminal Assignment for Model 2114R 1 Not Connected ** 2 Battery + 3 Ground 4 Not Connected** 5 Output signal (upper) 6 Output signal (lower) ! Terminal Assignments for Models 2211R, 2212R, 2213R 1 Sender in 2 Battery + 3 Ground 4 Hourmeter enable* 5 Output signal (upper) 6 Output signal (lower) 12 Terminal Assignments for Model 2214R ! 1 Not connected*** 2 Battery + 3 Ground 4 Hourmeter enable*** 5 Output signal (upper) 6 Output signal (lower) * Options terminal can be factory programmed to function as hourmeter reset or sender low (for use with two wire senders) **Options terminal-can be factory programmed to measure a separate variable voltage supply. ***Options terminals-can be factory programmed to measure a separate variable voltage supply. Hourmeter enable terminal could be factory programmed as an hourmeter reset. 13 5. TROUBLESHOOTING The following checklist should help you to troubleshoot any problems with the instrument. Turning the instrument off and then on again after about 10 seconds may solve the problem in the simplest cases. Make sure to observe the safety instructions in Section 1. ! Problem Possible Cause No display Voltage on Battery + terminal insufficient Display is not accurate Check sender installation. Teflon tape, some lubricants and anti-sieze compounds may prevent proper grounding of single wire senders. Check sender-to-gage wiring for excessive resistance. 14 6. MAINTENANCE Curtis 2100R & 2200R Series Engine Gages are ! not serviceable in the field. Units returned to the factory within the warranty period will be replaced without charge. 16 Guarantee - These Curtis Instruments’ products are guaranteed against defects in workmanship and material for a period of three years, or as defined in the individual product literature, from date of shipment from our factory, when applied in a proper application within specified ratings. This guarantee is limited to repair or replacement F.O.B. our factory. There is no further warranty or implied representation, guarantee, promise or agreement as to any Curtis Instruments product and/or component. Curtis Instruments, Inc., cannot assume responsibility or accept invoices for unauthorized repairs to its products and/or components, even though defective. In no case will Curtis Instruments’ responsibility extend to products, components or equipment not of its manufacture. Under no circumstances shall Curtis Instruments, Inc., be liable for any special or consequential damages or loss of profits or other damages. Returned goods will not be accepted unless identified by a Curtis Return Material Authorization (RMA). All specifications are subject to change without notice. CURTIS INSTRUMENTS, INC. 200 Kisco Avenue, Mt. Kisco, NY 10549 Tel. (914) 666-2971 • FAX (914) 666-2188 53018 REV A 10/97 ...
Este manual também é adequado para os modelos :equipamento de barco - 2200R (39.63 kb)