Log:
Assessments - , GPA: ( )

Instruções de Operação Attwood, Modelo 3834

Fabricante : Attwood
Arquivo Tamanho: 452.54 kb
Arquivo Nome :

Língua de Ensino: en

O documento está colocado, por favor, espere
O documento está colocado, por favor, espere

Facilidade de uso


#9230 (13-volt) or #910409 (24-volt). See chart above for voltage. REQUIRED FOR INSTALLATION • Phillips screwdriver • Cordless drill; 7/64" (#32 drill) and 3/8" (3 and 10mm) bits • Three #6 pan head stainless steel tapping screws (not included) • Marine-grade non-silicone sealant • 16-gauge wire and waterproof crimp connectors INSTALLATION LOCATION Before drilling mounting holes, position sidelights on a surface of the gunwale or deck where you are certain that sidelights: • Are equal distance from the bow (Figure 1) • Shine straight ahead • Shine within 5° of horizontal when the boat is floating • The light beam is not obstructed Place lights with the red lens on the port (left) and green lens on the starboard (right). Be sure there are no obstructions at the front or side within the light's arc of visibility (112.5 degrees each side). Figure 1 A □□ W INSTALLATION 1. To access light base mounting holes, remove exterior screw and stainless steel or plastic lens helmet. (Figure 2) 2. Remove lens screw and colored lens. Save screws, helmet, and lens for reinstallation. 3. Place light in position as shown in Figure 1. 4. Hold base with “FRONT” arrow pointing forward. Important: Before drilling, be sure that light will shine straight ahead and within 5° of horizontal when boat is floating. 5. Use base as a template to mark location of three mounting holes and a center hole for wire access. CAUTION Position wire access hole carefully, especially on aluminum boats, so that wires do not contact the hull. 6. Drill 3/8" (10mm) diameter hole for wire access and three 7/64" (3mm) diameter holes for mounting screws. (Figure 2). 7. Bring one 16-gauge (+) and one (-) wire up through access hole. DO NOT connect these wires to power until you read FINAL WIRING INSTRUCTIONS (Figure 3) 8. Connect wires using waterproof crimp connectors. 9. Fasten light to deck with three #6 stainless steel screws. DO NOT OVERTIGHTEN screws. 10. Replace lens over base. Replace lens screw. 11. Replace helmet over lens. Replace helmet screw. FINAL WIRING INSTRUCTIONS Use ONLY the rated voltage (see chart above). All positive wires must be protected by a 1-amp fuse. Higher voltage or failure to make proper wire and fuse connections will void the product warranty. Use crimp type marine-grade connectors with suitable insulation. Protect all connections with suitable materials. 1. Neatly thread wires to the switch, avoiding areas where abrasion or snagging may occur. 2. Use switch (Attwood #14386 or equivalent) that allows two-position ON/OFF/ON operation — one for running lights, and one for anchor lights. Attach wires with crimp-on butt joint connectors. Test lights for proper operation. MAINTENANCE To replace lamp: Remove the helmet and lens (Figure 2). Use small slotted screwdriver to pry old lamp out of terminals. Replace with the proper festoon-base lamp: Attwood #9230 (12-volt), or #910409 (24-volt). Replace lens, helmet, and retaining screws....

Este manual também é adequado para os modelos :
equipamento de barco - 3831 (452.54 kb)
equipamento de barco - 3830 (452.54 kb)
equipamento de barco - 3835 (452.54 kb)
equipamento de barco - 3838 (452.54 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias