Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
See "TAPE SELECTOR SETTING GUIDE" for details of various brands of cassette tapes and their proper selector positions. (11) Peak Level Indicator Gives instantaneous display of recording or playback level for both left and right channels. Each row of 10 LEDs directly shows levels from —18dB to +9dB. (12) Dolby NR Indicator Glows when Dolby NR switch is on, indicating the unit is in Dolby NR recording or playback mode. (13) Metal Tape Indicator Glows when METAL button of the Tape Selector is depressed. (14) PAUSE Indicator Glows to indicate tape motion is temporarily stopped when PAUSE button on the cassette control section is depressed. (15) Recording Indicator 12 Glows to indicate recording is in process when REC button on the cassette control section is depressed. (16) Tape Counter and Reset Button The three-digit tape counter indicates the amount of tape travel. Push the reset button to set the counter to "000." This counter is convenient in finding the beginning of a specific section of the tape or checking the amount of the remaining tape on a cassette. (17) Tape Holder J Cassette tape is loaded onto this holder. TAPE SELECTOR SETTING GUIDE TAPE SELECTOR POSITION MANUFUCTURE BRAND BIAS ADJUST CONTROL NORMAL TDK OD 0 AD 0 FUJI FILM Range 6 5 SONY AHF 0 BHF - 5 MAXELL UD - I XLI - I SCOTCH MASTER I20 - г FeCr SONY DUAD 0 BASF FCR - 3 о о TDK S A - 5 FUJI FILM RANGE 4X - 5 SONY JHF 0 MAXELL XL II 0 SCOTCH MASTER II - 5 BASF SCR - 2 METAL TDK MA 0 FUJI FILM Suqer Range 0 SONY METALLIC 0 MAXELL MX - 5 SCOTCH METAFINE - 2 ENGLISH tab and gently pry the tab off. Be sure the tab falls free from the cassette. 2. If one side only has been recorded, place the cassette on a table just as it has been removed from the recorder, with the side recorded facing up and the exposed tape area facing you. You should then remove the tab in the left-hand corner to prevent erasure of that side of the tape. If you later wish to record over a previously recorded tape, simply place a piece of adhesive tape over the opening. This will allow you to make a new recording. Removal of the tape after recording will again insure against accidental erasure. The cassette tape, when wound loosenly on either hub, is likely to jam around the capstan and pinch roller during recording or playback. Therefore, if the tape is loose, insert a pencil into the more tightly wound hub, and turn it with the pencil until the slack is taken up. Always be sure to check that the tape is wound tightly before inserting a cassette in your deck. ENGLISH BEFORE RECORDING OR PLAYBACK 1. Be certain that power connection and connection with amplifier are properly made. 2. When recording, be sure the safety tabs on the cassette tape are not removed. 3. Be sure to unplug the microphones from the deck when recording from other sources. 4. To load the cassette tape, hold it by the sides and fit the top under the upper projecting section of the cassette holder. Then gently push in the bottom portion of the cassette tape so that the two catches on the lower holder secure the cassette snugly. To unload the cassette, hold it by the sides, and first detach it from the lower holder by pulling gently. Then detach from the upper holder. 5. Be sure to attach the protection cover to the tape holder when the unit is not in use. RECORDING • When recording with microphones, the microphone plugs must be inserted properly into the left and right microphone jacks. • When recording from line sources, choose the desired program (tuner, turntable, etc.) on your amplifier. 1. When you wish to record using Dolby NR circuit, set the Dolby NR switch to ON position. 2. Set the Tape Selector according to type of tape used.* 3. Turn on the deck Power switch. 4. Press REC and PAUSE buttons simultaneously. 5. Adjust the recording level for left and right channels with Recording Level control so that the level indicator reading does not exceed OdB position too frequently. (See figure.) 6. After adjusting recording level, press the PAUSE button again to put the unit into recording mode and to start the tape. 7. Be careful to watch the level indication during recording as well. PAUSE button may be used to halt recording temporarily. 8. Press STOP button when recording is finished. When the end of the tape is reached, the REC button will automatically disengage and the tape stops. * When setting the Tape Selector, also set the Bias Fine-adjust control to the appropriate position. See "TAPE SELECTOR SETTING GUIDE" for optimal setting. PLAYBACK 1. When using Dolbyized tapes, set the Dolby NR switch to ON. For non-Dolbyized tapes, set the switch to OFF. 2. Set the Tape Selector to match the type of tape used. 3. Turn on the power switch on your amplifier, keeping its volume control set to minimum. When using headphones connected to the tape deck, the amplifier is not necessary. 4. Turn on the Power switch on the deck. ...