Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Load the disc (use the OPEN/CLOSE key and load the disc recorded side downwards and close the tray). 2 Press the CD-TAPE CONT PLAY key. 3 Press either of the PLAY keys of the tape deck, or the PLAY key of the CD deck. Playback will start on the appropriate unit. When playback reaches the end of the disc, or the end of the tape (either one side or two NOTE Avoid touching the tape. Fingerprints attract dust and dirt. 2 Press the EJECT key to open the cassette compartment door. 3 Load the cassette tape with its open edge facing down. 4 Gently close the compartment door. NOTE The cassette holder cannot be opened during recording or playback. If the power has been switched off during play or recording, ejecting the cassette may be impossible. In such a case, switch the power on and press the EJECT key again. 2 Load a pre-recorded cassette with its open edge facing down and side A facing toward you. 3 Set the Dolby NR system on or off. 4 Press either PLAY key to start playback. 5 Adjust the volume with the amplifier's volume control. 6 To stop playback, press the STOP key. sides, as determined by the REV MODE setting), playback starts on the other unit. Media (tape or disc) can be changed in the unit that is not playing. NOTE The cassette deck and CD deck can be used to play back through different outputs, or the LINE OUTPUTS 2 jacks can be used for both disc and tape playback. However, note that if both are playing, the cassette takes priority (the disc will not be heard through these outputs). Disc playback is always through the LINE OUTPUTS 1 jacks. 16 TASCAM CC-222MKII Owner’s Manual 3 - Cassette operations—Recording operations Recording operations Recording pre-recorded tapes, records, or other published or broadcast material may infringe copyright laws. Check before recording. 1 With the power on, set the REV MODE switch. If you want to make a bi-directional recording, set the REV MODE switch to the or CO position. Set to the u (single side) position if recording is to be made on a single side of the tape. 2 Load a recordable cassette. Check that the safety tabs on the spine of the cassette are in place. If they have been broken off, block the holes with adhesive tape. 3 Press the INPUT 2 SEL key to select the source (either LI NE2 or DISC). When DISC is selected, the built-in CD player's output is selected as a source. When LINE2 is selected, the external signal from the LINE 2 jacks is selected as a source. 4 Set the Dolby NR system on or off. 5 Press the RECORD key. The deck enters record pause mode (the display indicators light). 6 Play back the source, and adjust the recording level with the INPUT level control so that the loudest sound to be recorded just makes the meters briefly reach around the “0 dB” point for normal or high-position tapes (recording is not possible with metal tapes). 7 Press either the PAUSE or PLAY key to start recording. To stop recording temporarily, press the PAUSE key. To restart the tape, press either the PAUSE key or either of the PLAY keys. When the unit is in record pause mode, if the PLAY key whose indicator is lit is pressed recording will restart. If the PLAY key whose indicator is unlit is pressed, the recording direction will reverse, and the PLAY key must be pressed again to restart recording. To stop recording, press the STOP key. Dubbing tapes from the CD deck To record from the internal CD deck: 1 Prepare for recording as described above (load a tape, set the REV MODE, etc.). 2 Load the source CD disc (press OPEN/ CLOSE, put the disc in the tray, recorded side downwards, and close the tray). 3 Use the MENU key to set the dubbing volume to TH RU to bypass the input level control (see “Bypassing the INPUT level for dubbing” on page 18). NOTE If you want to record the tracks on the tape in a different order from those on the disc, use the programmed playback mode to rearrange the tracks ("Programmed order playback" on page 22). Leave the disc in stop mode when you have finished programming the order. 4 Press the DUB 2 key. If the tape is in stop mode If the tape is in stop mode, the tape rewinds to the beginning of the current side. At the start of the tape, recording starts, but the CD does not start playback for eight seconds (this is to allow for the leader tape at the start of a cassette). The DUB indicator flashes. The CD starts playback after the eight seconds at the start of the cassette. The DUB indicator lights steadily. If the tape is in record pause mode If the tape is in record pause mode, recording starts immediately, and the CD starts playback immediately. The DUB indicator lights. If you want to adjust the input volume, set the DUB>VO L menu to ON and use the left (tape) INPUT control to adjust the level of signals fed to the tape from the CD player. TASCAM CC-222MKII Owner’s Manual 17 3 - Cassette operations—Recording tapes from the PHONO deck The dubbing stops when playback reaches the end of the...