Assessments - 2, GPA: 4.5 ( )

Fabricante : Magnavox Arquivo Tamanho: 432.9 kb Arquivo Nome : Língua de Ensino:

You must select channels at the Cable Box. 3. Use a second RF OUT IN 75WANT /CABLE ANTENNA IN Jack Back of TV (example only) 1. Connect the Cable signal to the IN Jack on the Cable Box. coaxial cable to con- nect the ANT(enna) OUT jack on the VCP to the TV’s ANTENNA IN Jack. 2. Use the RF coaxial cable (supplied) to connect the OUT Jack on the Cable Box to the ANT(enna) IN Jack on the VCP. Watching TV with the VCP Off 1 Set the TV to the Cable Box output channel (channel 3 or 4). 2 Select the channel you want to watch at the Cable Box. You can not select channels at the TV. Playing a Tape 1 Set the TV to channel 3 or 4, whichever channel the CH3/CH4 switch on the VCP is set to. 2 Press the PLAY button to play the tape. Hookups With a Cable Box (cont’d) 9 This connection differs from the one shown on page eight. You may still view any channel (selecting channels at the Cable Box), but the instructions for playing a tape are different. 1. Connect a Cable signal to the VCP’s IN OUT 75WANT /CABLE ANT(enna) IN Jack. 3. Use a second RF coaxial cable to connect the OUT Jack on 2. Use an RF coaxial cable (supplied) to connect the ANT(enna) OUT Jack on the VCP to the IN Jack on the Cable Box. TV ANTENNA IN Jack the Cable Box to the ANTENNA IN Jack on the back of the TV. Watching TV with the VCP Off 1 Set the TV to the Cable Box output channel (channel 3 or 4). 2 Select the channel you want to watch at the Cable Box. Playing a Tape 1 Make sure the Cable Box is on the same channel as the VCP’s CH3/CH4 switch. 2 Set the TV to the Cable Box output channel (channel 3 or 4). 3 Press the PLAY button to play the tape. 10 Hookups With a Stereo TV antenna or cable to ANT(enna) IN Jack VIDEO (yellow) and AUDIO (white) OUTPUT Jacks Video Cable Audio Cable l Audio and Video cables are not supplied. 1 Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCP. 2 Connect a video cable to the yellow VIDEO OUTPUT Jack on the back of the VCP. Then, connect the other end of the video cable to the VIDEO IN Jack on your TV. 3 Connect an audio cable to the white AUDIO OUTPUT Jack on the back of the VCP. Then, connect the other end of the audio cable to the AUDIO IN Jack on your TV. (If your TV has Right and Left AUDIO IN Jacks, you must use a “Y” splitter audio cable as illustrated to deliver audio to the TV’s left and right channels.) 4 Turn on your TV, making sure it is in Line Input mode. Please refer to your TV owner’s manual for details. Audio and Video IN Jacks on TV Helpful Hint • This hookup will not give you stereo sound. To get stereo sound, use the connections on pages six-nine and select the channel to be viewed at the TV or the Cable Box (with the VCP turned off). Mobile Connections 11 When passengers in your vehicle want to watch a video program, hook up the VCP by following the steps below. AC Power Cord Car Battery Cord (supplied) To 13.2V Jack To Cigarette Lighter Jack 1 Make sure your vehicle has a 13.2-volt, negative ground electrical system. Unplug the AC power cords of the VCP and the TV. 2 Connect one end of the car battery cord to the 13.2V Jack on the back of the VCP. 3 Connect the other end of the car battery cord to the cigarette lighter jack in your vehicle. 4 Follow step 3 on page seven to connect the VCP to a TV. 5 Connect the TV to a DC power source. The TV must have an AC/DC Jack. Helpful Hints • Do not watch TV while driving. • Use only the supplied car battery cord. Using another cord could damage the VCP or cause faulty operation. • Make sure the cigarette lighter jack is free of ashes and other debris. • Make sure you push the car battery cord’s plug completely into the cigarette lighter jack. • Always unplug the car battery cord from the cigarette lighter jack before you unplug it from the VCP. • You must disconnect the car battery cord from the VCP before you can use standard AC electrical power. • If the vehicle’s engine is off, there will not be enough electrical voltage to operate the VCP. • Unplug the car battery cord from the cigarette lighter jack when you have finished using the VCP. 12 Remote Control Buttons EJECT Button Press to eject the tape. POWER Button Press to turn the VCP on or off. TRACKING (Up/Down) Buttons During tape playback, press to adjust the tracking manually. Details are on page 19. Press to remove vertical jitter in a Still picture. Details are on page 18. FF/SEARCH Button When tape playback is stopped, press to fast forward the tape at high speed. During tape playback, press to fast forward the tape while the picture stays on the screen. REW(ind)/SEARCH Button When tape playback is stopped, press to rewind the tape at high speed. During tape playback, press to rewind the tape while the picture stays on the screen. PLAY Button Press to play a tape. Also, press to release Search mode or Still mode and return to normal playback. Details are on page 18. STOP Button Press to stop tape playback or forward or reverse searching. Pressing the STOP button also retur...

Baixe o seu

Para fazer o download, introduza 2 dígitos :