Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Always shut the CD door to keep the CD compartment dust-free.To clean, dust the compartment with a soft dry cloth. • To take a CD out of its box, press the center spindle while lifting the CD.Always pick up the CD by the edge and replace the CD back in its box after use to avoid scratching and dust. • To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. • Never write on a CD or attach any stickers to it. Top and front panels (see 1) 1 STOP 9 – stops CD playback; erases a CD program 2 PLAY/PAUSE 2; – starts or pauses CD playback 3 CD display – shows the CD functions 4 LIFT TO OPEN – opens the CD door 5 VOLUME – adjusts volume level 6 PROGRAM – programs and reviews programmed track numbers 7 SEARCH ., § – CD: skips or searches a passage/track backward or forward. 8 TUNING – tunes to a station 9 Source selector OFF/FM/AM/CD – select CD, FM or AM source of sound – power off switch Back panel 10 Telescopic antenna – to improve FM reception 11 Battery door – open to insert 6 x 1.5V R14/ UM2/ C-cell batteries 12 AC MAINS – inlet for power cord Power supply Whenever convenient, use the power supply if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries. Batteries (not included) 1 Open the battery compartment and insert six batteries, type R-14, UM2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "-" symbols inside the compartment. 2 Replace the compartment door, making sure the batteries are firmly and correctly in place.The set is now ready to operate. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst.Therefore: • Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not try to mix old batteries with the new ones. • Remove the batteries if the set is not to be used for a long time. Using AC Power 1 Check if the power voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 2 Connect the power cord to the AC MAINS inlet and the wall outlet.The power supply is now connected and ready for use. 3 To switch off completely, unplug the power cord from the wall outlet. • Unplug the power cord from the wall outlet to protect your set during heavy thunderstorms. The type plate is located on the bottom of the set. Switching Power on/off: Save energy Whether you are using mains or battery supply, to avoid unnecessary energy consumption, always adjust the source selector to OFF after using the set. General operation 1 To select your sound source, adjust the source selector to CD, FM or AM. 2 Adjust the sound with the VOLUME control. 3 To switch off the set, adjust the source selector to OFF position. Tuner reception 1 Adjust the source selector to FM or AM. 2 Turn TUNING to tune to a station. • For FM, pull out the telescopic antenna. Incline and turn the antenna. Reduce its length if the signal is too strong (very close to a transmitter). • For AM, the set is provided with a built-in antenna so the telescopic antenna is not needed. Direct the antenna by turning the whole set. 3 To switch off the radio, adjust the source selector to OFF position. CD player Display indication for CD functions: – OO: Cd door open – --: reading disc contents / no disc/ error in CD operation or with the CD/ CD-R/W is blank or not finalized (see Troubleshooting) – In stop mode: total track number – During CD playback: 9 and current track number – 2: playback on pause – PROG: when CD program active Playing a CD This CD player plays Audio Discs including CD-Recordables and Rewritable. • MP3 CD-ROMs, CD-I, CDV,VCD, DVD or computers CDs are not possible for playback. 1 Adjust the source selector to CD. 2 Open the CD door, and insert a CD/ CD-R/W with the printed side facing up and press the CD door gently close. 3 Press PLAY/ PAUSE 2; on the set to start playback. 4 To pause playback, press PLAY/ PAUSE 2;. . 2 flashes. 5 To resume, press PLAY/ PAUSE 2; again. 6 To stop CD play, press STOP 9. 7 To switch off the set, adjust the source selector to OFF position and check if the cassette keys are released. Note: CD play will also stop when: -- you open the CD compartment; -- you select FM or AM sound source; -- the CD has reached to the end. Selecting a different track During playback you can use ./ § to select a particular track. – If you have selected a track number in the stop or pause position, press PLAY/ PAUSE 2; to start playback. • Press § once briefly for the next track, or press repeatedly until the desired track number appears in t...
Este manual também é adequado para os modelos :Receptores - MCS211BK (1.97 mb)