Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
– Do not expose the set, CDs, batteries or cassettes to humidity, rain, sand, direct sunlight or other places where high temperatures can occur, such as in the vicinity of heating apparatus or in motor cars parked in the sun. – Do not cover the set. The amplifier produces heat which must dissipate freely, so make sure that there is sufficient ventilation around the set. A minimum gap of 15 cm is necessary. – The mechanical parts of the CD player and the cassette deck contain self-lubricating bearings and must not be oiled or lubricated. – A chamois leather slightly moistened with water is sufficient for cleaning the housing. Do not use cleaning agents containing alcohol, spirits, ammonia or abrasives as these may harm the housing. CD MAINTENANCE – The lens of the CD player should never be touched. – The lens may cloud over if the CD player is moved from cold to warm surroundings. The CD player will not start. Give the player some time to acclimatise. – To take a CD out of its box, press the center spindle while lifting the CD. Always pick up the CD by the edge and replace the CD back in its box after use to avoid scratching and dust. – To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. – Never write on a CD or attach stickers to it. RECORDER MAINTENANCE (see 0) To ensure a good recording and playback quality, clean the indicated parts A,B and C after every 50 hours of operation or, on average, once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid. • Press PLAY 1 5 and clean the rubber pressure rollerC. • Then press PAUSE ; 5 and clean the capstan B and the heads A. • After cleaning, press STOP•OPEN 9 / 5. Cleaning of the heads A can also be done by playing a cleaning cassette through once. POWER SUPPLY BATTERIES (see 1) Whenever convenient, use the power supply if you want to conserve battery life. Make sure you remove the power plug from the set and wall outlet before inserting batteries. Batteries (optional) 1. Open the battery compartment and insert as shown eight batteries, type R14, or C-cells. 2. Replace the compartment door, making sure the batteries are firmly and correctly in place. 3. Remove the batteries if exhausted or if they will not be used again for a long period. – The incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore: – Do not mix battery types, e.g. alkaline with zinc carbonate. – When inserting new batteries, replace all batteries at the same time. – Remove the batteries if the set is not be used for a long time. Note: The battery supply is switched off when the set is connected to the power. AC POWER 1. Check if the power voltage as shown on the type plate (on the bottom of the set) corresponds to your local power voltage. If it does not, consult your dealer or service organisation. 2. Connect the power cord to the AC MAINS outlet and the wall outlet. – The set is now ready to use. 3. To switch off the AC power supply completely, pull the power plug out of the wall outlet. – Disconnect the power cord when you change over to battery supply, or to protect the set during heavy thunderstorms. Both the model and production numbers can be found on the bottom of the set. Environmental information All redundant packaging material has been omitted. We have done our utmost to make the packaging easily separable into three mono materials: cardboard (box), expandable polystyrene (buffer) and polyethylene (bags, protective foam sheet). Your set consists of materials which can be recycled if dissassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. OPERATION/TUNER CD PLAYER GENERAL OPERATION 1. To switch on the set, use the source selector 2 2. Adjust the sound using the VOLUME control 1 and DBB switch 3. 3. To switch off the set, set the source selector 2 to TAPE/OFF position, with the cassette keys released. TUNER (see 2 / 3) 1. Set the source selector 2 to TUNER. 2. Adjust the sound using the VOLUME control 1 and the DBB switch 3. 3. Select the wave band using the FM-AM band selector @. 4. Tune to a radio station using the TUNING knob #. – For FM, pull out the telescopic antenna. To improve FM-reception, incline and turn the antenna. Reduce its length if the FM-signal is too strong (very close to a transmitter). – For AM, the set is provided with a built-in antenna, so the telescopic antenna is not needed. Direct the antenna by turning the whole set. – The FM STEREO indicator 9 lights up when you are receiving a FM stereo transmitter in stereo. 5. To switch off the set, set the source selector 2 to TAPE/OFF position, with the cassette keys released. CD DISPLAY INDICATION (see 4) – Total track number: in stop position. – Current track number: during CD play. – ; an...
Este manual também é adequado para os modelos :CD-players - AZ1108/17 (2.6 mb)
CD-players - AZ1105/17 (2.6 mb)