Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 5 Adjust the volume. To use auto scan You can search for a station by listening to all tuned-in stations for 8 seconds each. Preparation: Switch [ ] to “TUNER”. 1. Press [BAND] to select “FM” or “AM”. 2. Press [AUTO SCAN]. Auto scan starts. 3. Press [AUTO SCAN] when you find the desired station. Auto scan ends when it reaches the original frequency again. To stop during the process, press [AUTO SCAN]. To improve reception FM: Extend the whip antenna and adjust its direction. AM: Adjust facing of the unit. If noise is excessive in the FM stereo mode Press [FM MODE]. (“ ” lights up.) Sound will be produced in monaural, but this also reduces noise. Press the button again to cancel. (“ ” goes out.) To receive FM broadcasts allocated in 0.1 MHz (Only from the main unit) First press [BAND] to select “AM”. Now, press and hold [BAND]. The display changes in a few seconds to show the current lowest FM frequency. Continue to hold down the button. The minimum frequency changes and the step is changed at the same time. Changing the step erases all preset stations. Repeat the above to change the step back. Preset the stations (12 FM and 12 AM) to make tuning simpler. 1 Tune to the desired station. Do steps 1–4 on the left. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 2 Press [MEMORY]. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 3 While “ ” and the frequency are flashing Press [MEMORY]. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 4 While “ ” and the preset channel are flashing Press [–/g] or [f/+] to select the desired channel. (Remote control: [4] or [3]) a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 5 Press [MEMORY]. (This completes presetting.) a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 6 Repeat steps 1–5 to preset other stations. Note If “ ” goes off during presetting, return to step 2. 1 Press [BAND] to select “FM” or “AM”. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 2 (Omit this step if using the remote control) Press [TUNE MODE] to display “ ”. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 3 Press [–/ g] or [f/+] to select the desired channel (1–12). (Remote control: [4] or [3]) To use preset scan You can search for a station by listening to all preset channels for 8 seconds each. 1. Do steps 1 to 2 above. For remote control, replace [–/ g] or [f/+] described below with [4] or [3]. 2. Press and hold [–/ g] or [f/+] until “PS” appears on the display. 3. Press [–/ g] or [f/+] when you find the desired channel. Preset scan ends after searching through each preset channel once. To stop during the process, press [–/ g] or [f/+]. Normal tuning Preset tuning Listening to radio broadcasts To listen to preset channels How to preset Indicates auto scan Indicates preset scan “ ” lights when an FM stereo broadcast is being received. Preset channel Preset channel 3 2 1 5 4 2 3 1 2 3 5 4 RQT6742 4 1 Switch [ ] to “CD”. (Power comes on.) a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 2 Push [c CD OPEN/CLOSE] to open the CD lid and insert the CD. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 3 Push [c CD OPEN/CLOSE] to close the CD lid. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 4 Press [-/ J] to start play. Play starts from the first track and continues to the last track. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 5 Adjust the volume. To stop play Press [L]. “NO DISC” is displayed if there is no disc in the unit. Note • If interference occurs to radios or televisions, place the unit as far as possible from this equipment. • Do not press [c CD OPEN/CLOSE] during play, pause or immediately after you inserted the CD and closed the CD lid. CD may be scratched. This unit can play CD-DA (digital audio) format audio CD-R that has been finalized (a process that enables CD-R players to play audio CD-R) upon completion of recording. It may not be able to play some CD-R due to the condition of the recording. It cannot play CD-RW. You can program up to 24 tracks. Ensure CD is stopped before programming. 1 Press [–/g] or [f/+] to select the desired track. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 2 Press [MEMORY]. The track is programmed. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 3 Repeat steps 1 and 2 until you have programmed all the tracks you want. a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 4 Press [-/ J]. Play starts in the programmed order. To stop play Press [L]. “P” is displayed indicating that the program is still active. Press [L] again and “CLr” is displayed; the program is cleared, and the normal play mode is restored. To check program contents Press [–/ g] or [f/+] when “P” is displayed. Display “— —:— —”: Program equals, or exceeds, 100 minutes but programming and play are still possible. “FU...