? The Security Code item isn’t displayed in the Menu System. . The Security Code function is already activated. . When the Security Code function is activated it isn’t displayed in the menu items. ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. ? Even though the vehicle light switch is display won’t dim. . The dimmer wire isn’t connected. . Connect the dimmer wire correctly. ? The Dimmer function doesn’t work. . The Dimmer wire isn’t connected correctly. . Check the Dimmer wire connection. — —— 27 2727 — —— English English Tuner source ? Radio reception is poor. . The car antenna is not extended. . Pull the antenna out all the way. . The antenna control wire is not connected. . Connect the wire correctly, referring to the section on . ? The desired frequency can’t be entered with the Direct Access Tuning. . A station that can’t be received is being entered. . Enter a station that can be received. . You’re trying to enter a frequency with a 0.01 MHz unit. . What can be designated in the FM band is to 0.1 MHz. Cassette tape source ? Can’t remove tape. . The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. . The tape can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. ? The DPSS, Tape Advance and Music Repeat don’t operate correctly. . The space between the songs on the tape can’t be recognized because it’s too short. . Have at least 4 seconds between songs. . The space between songs can’t be recognized because there’s too much noise between songs. . Reduce the noise between songs. ? The blank skip doesn’t work. . Because noise is too loud, the non-be recognized. . Reduce the noise between songs. ? Blank Skip functions at . Because the recording it’s recognized as not recorded. . Turn Blank Skip OFF. Disc source ? "AUX" is displayed without achieving External disc control mode. . O-N switch is set to "O" side. . Set the switch to "N" side. . Unsupported disc changer is connected. . Connect the supported disc changer. (page 3) ? The specified disc does not play, but another one plays instead. . The specified CD is quite dirty. . Clean the CD. . The CD is upside-down. . Load the CD with the labeled side up. . The disc is loaded in a different slot from that specified. . Eject the disc magazine and check the number for the specified disc. . The disc is severely scratched. Try another disc instead. ? The specified track will not play. . Random play or magazine random play has been selected. Turn off random play or magazine random play. ? Track repeat, disc repeat, track scan, random play, and magazine random play start by themselves. . The setting is not canceled. . The settings for these functions remain on until the setting or the disc ejected, even if the power is turned off or changed. ? Cannot play CD-R or CD-RW. . Finalization processing is not being conducted . Conduct finalization processing with CD . A non-compatible CD changer is being Use a CD changer compatible ? Direct Track Search and Direct Album be done. . Another function is ON. . Turn Random Play or other ? Track Search can't . For the albums . For each album, Search — 28 — direction for the first song or in the forward direction for the last song. direction for the first song or in the forward direction for the last song. • Even though the disc changer is connected, the Disc Changer source is not ON, with "AUX" showing in the display during the Changer Mode. • Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the Auxiliary input is entered when switching modes. — 29 — English English The messages shown below display your systems condition. EJECT: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. . Load the disc magazine properly. No CD in the unit. . Insert the CD. NO DISC: No disc has been loaded in the disc magazine. . Load a disc into the disc magazine. TOC ER: No disc has been loaded in the disc magazine. . Load a disc into the disc magazine. The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. . Clean the CD and load it correctly. BLANK: Nothing has been recorded on the MD. NO TRACK No tracks are recorded on the MD, although it has a title. NO PANEL: The faceplate of the slave unit being connected to this unit has been removed. . Replace it. E-77: The unit is malfunctioning for some reason. . Press the reset button on the unit. If the "E-code does not disappear, consult your nearest service center. MECHA ER: Something is wrong with the disc unit is malfunctioning for some . Check the disc magazine. And button on the unit. If the "not disappear, consult your nearest service HOLD ER: NO NAME: NO TITLE: NO TEXT: LOAD: READING: NO ACCES: ...
)
