Tune numbers and absolute time will be continued from the previously recorded contents. • The end ID signal of the previous recording is automatically erased. To erase the end ID signal An end ID signal is automatically erased when successive recording is performed using the end search function. To erase an end ID signal without successive recording, perform the following procedure. When the tape stops after end search operation, press the END ID ERASE button. The button starts flashing. When the end ID signal is erased, the tape stops. (While erasing the end ID signal, the tape is advanced for a few seconds and the END-ID indicator flashes.) To erase the recorded contents When a recording is made over a previous recording, the previous recording is automatically erased. To erase the recorded contents without making a new recording, perform the following procedure. 1 Set the INPUT selector to the ANALOG position. 2 Load the tape in the cassette holder. 3 Turn the REC LEVEL control fully counterclockwise to 0 (MIN). 4 Press the REC button (•). 5 Press the PLAY button (►). The previously recorded contents will be erased. 21 PLAYBACK Normal playback 1 Load the tape into the cassette holder. 2 Press the PLAY button (►). To stop playback_ 1 Press the STOP button (■). 2 To start playback again, press the PLAY button (►). To stop playback temporarily__ 1 Press the PAUSE (li) button. 2 To resume playback, press the PLAY button (►) or PAUSE (li) button again. • To protect the tape, the pause mode automatically cancels after 5 minutes and the unit enters stop mode. R EW FF l I STOP □ Pr « C\ ►► Pv To fast-forward or rewind the tape 1 To fast-forward the tape, press the STOP button (■), then the FF button (►►). To rewind the tape, press the STOP button (■), then the REW button {«). 2 Press the STOP button (■) to stop the tape running. 22 ÀPSS (Auto Program Search System) APSS allows you to locate the beginning of any tune during playback. Simply press the REW (-♦<) or FF (►►) button to move backward or forward. NOTES: • For tapes with a start ID signal interval shorter than 9 seconds, APSS may not function properly (page 20). • If a tune is not played according to the tune number selected with APSS, the start ID signal and tune number have not been correctly written. See page 19. Press the FF button (►►) to go to the beginning of the next tune. Press the REW button (-♦*) to return to the beginning of the current tune. Each press of the FF button (►►) skips to the beginning of the subsequent tunes. Each press of the REW button (-«*) skips to the beginning of the previous tunes. • The tape can be paused at the beginning of the desired tune by pressing the PAUSE button (II) after pressing the FF (►►) or REW (■+*) button. The desired tune can then be played by pressing the PLAY button (►). L' D UmUL LÇxJ To go to tune 4 while tune 3 is playing Press the FF button (►►) once while tune 3 Is playing. The tune number indicator changes from 3 to a flashing 4 and the tape is fast-forwarded to the beginning of tune 4. Playback starts from the beginning of tune 4. U > I Cm U U» To replay from the beginning of tune 4 while tune 4 is playing Press the REW button (-#4) once while tune 4 is playing. ew The tune number indicator changes to a flashing 4 and the ==f tape is rewound to the beginning of tune 4. Playback starts ** again from the beginning of tune 4. FF w To skip to tune 8 while tune 5 is playing Press the FF button (►►) three times while tune 5 is playing. The tune number indicator changes from 5 to a flashing 8 and the tape is fast-forwarded to the beginning of tune 8. Playback starts from the beginning of tune 8. LI (j C :« U L To skip to tune 6 while tune 10 is playing Press the REW button (-<4) five times while program 10 is playing. The tune number indicator changes from 10 to a flashing 6 and the tape is rewound to the beginning of tune 6. Playback starts from the beginning of tune 6. HP. z> n n n t-IU LUuLJUi 23 To program desired tunes (APMS=Automatic Programmable Music Selector) You can program desired tunes in any desired order. • If the tunes are not numbered properly, the desired tunes may not be programmed, or program playback may stop 1 Load the tape. 2 Press the PROGRAM button. The APMS indicator lights. 3 Using the digit buttons (1-0, +10, +20), enter the desired tune numbers in the desired order. Example: To select tune 12: Press "+10" and "2". To select tune 20: Press "+20“ and "0". To select tune 54: Press "+20" twice, "+10" and “4". The display shows the program number (playback order) and the programmed tune number. 4 Press the PLAY button (►). The programmed tunes are played in the programmed order. To skip to the beginning of a tune in the program: Press the FF (►►) or REW (-♦*) button to skip to the beginning of previous/subsequent programmed tunes. To check the program contents In stop mode, press the...
)
