Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
The set should be placed to a position for the best reception. Cassette tape playback_ • Slide the FUNCTION switch to TAPE (OFF) position. • Press the STOP/EJECT button to open the cassette door. • Insert a cassette with the tape-side up into the proper Guide-rails on the inside of the cassette door. • Gently push the cassette door forward (inwards) to close it. • Press the PLAY button to start the playing. • Adjust the level of sound with VOLUME knob. Cassette controls • Press the PAUSE button to pause the playing. • Press the STOP/EJECT button to stop the playing, press the button again to open the cassette door and you can take out the tape. Cassette tape recording_ • Open the cassette door by pressing the STOP/EJECT cassette button. 4 • Insert a blank cassette with the tape-side up, into the proper Guide-rails on the inside of the cassette door. • Gently push the cassette door forward (inwards) to close it. • Make sure the tape is fully and properly inserted before doing so. • The set is now ready to start recording, which can be done from either the radio or CD-player. Recording from radio • Set the FUNCTION switch to RADIO position. • Tune to the needed station. • Press the PLAY button and RECORD button on deck simultaneously to start recording. • Press STOP/ EJECT button to end recording. Recording from CD • Set FUNCTION switch to CD position. • Press RECORD and PLAY buttons on cassette deck simultaneously to start recording. • Press the PAUSE button on deck. • Turn on the CD-player and select the exact song to be recorded. • Release the PAUSE button on deck to start recording. • Press STOP/EJECT button to end recording. Erase protection • To prevent accidental erasing of a cassette, simply break off the two plastic tabs located on the cassette tape's rear side. • When a cassette with removed plastic tabs is inserted, the recording button cannot be pressed. • If a cassette is to be erased and re-recorded at a later stage, simply cover the holes on the cassette where the tabs were removed, with a piece of strong adhesive tape. TAB FOR SIDE A 5 Compact disc operations • Set Function switch to CD/MP3 position. • Open the CD door by pulling up CD door. • Put a CD into the CD compartment with label side up and close the CD door by pulling it down gently. Play/pause mode • Press the PLAY/PAUSE button to start play. • Press the Play/Pause button to pause at any track when playing. • To stop the CD, press the STOP button. • To remove the CD from the unit open the CD door by pulling up CD door. • Always press STOP button before opening the CD compartment. Skip and search mode • Press NEXT button once to skip to the next track. Press and hold this button to search for a particular point at high-speed forward. Release the button to resume normal play. • Press BACK button once to skip back to the beginning of the current track, twice to skip back to the beginning of the previous track. Press and hold this button to search for a particular point at high speed backward. Release the button to resume normal play. • Press SKIP +10/FOLDER to play every 10th track on disc. Playback modes • Press REPEAT button repeatedly to switch between different playback modes. • During playing the mode will change as below: - For CD playback: REPEAT => REPEAT ALL => RANDOM => NORMAL. - For MP3 playback: REPEAT => REPEAT ALL => RANDOM => NORMAL. Program mode • Up to 21 CD and 99 MP3 tracks can be programmed for disc play in any order. • Before use, be sure to stop the CD by pressing the CD STOP button. • Press the REPEAT/PROGRAM button. The set is now in memory programming mode, at the first memory position. • Select a desired track by using NEXT and BACK buttons. • Press REPEAT/PROGRAM button again to confirm. • The set will advance to next memory position. • Repeat steps described above to enter additional memories into the program if necessary. 6 • After a maximum of 21 CD and 99 MP3 tracks (or less) have been selected as described above, press the CD PLAY/PAUSE button to start playing the programmed tracks. • The program memory will be cleared when you press CD STOP button or turn off the CD or power supply. Note: In case of MP3 Disc all procedure is same as normal disc. Note: Good quality sound is guaranteed only when playing licensed CD-R/CD-RW discs. MP3 operations_ • In MP3 playback mode all functions are available as in CD operation mode. • If your MP3-CD has folders, you can select the folder to playback. Press and hold SKIP +10/FOLDER button to switch to the next folder. The set will start playing the first song in the selected folder. Note: Good quality sound is guaranteed only when playing licensed MP3 discs. Maintenance and care • Check your batteries regularly; old or discharged batteries should be replaced. If the unit is not going to be used for some time or is being run exclusively on the alternative power, remove the batteries to avoid leakage ...