Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
About 4-5 seconds later, the tape automatically stops, and the unit enters the record-pause mode. 3. Press the PLAY button to start recording again. B. To leave non-recorded sections of more than 4-5 seconds 1. Keep the •REC/REC MUTE button pressed continuously as long as you want to make a non-recorded section. By releasing the finger from the button after the above operation, the unit enters the record-pause mode. 2. Press the PLAY button to start recording again. C. To leave non-recorded section of less than 4-seconds When the undesired section comes during recording.... After the •REC/REC MUTE button is pressed, press the PLAY button before the unit enters the pause mode to start recording again, or press the llPAUSE button to enter the record-pause mode. • The peak level indicator lights even during record muting according to the input level which can be heard from the speakers or headphones so that recording can be resumed at the exact point on the tape. ERASING When recording on a prerecorded tape, the previous recording is automatically erased and only the new program is recorded on the tape. To erase a tape without making a new recording... Follow the section “RECORDING” but in step O, set the INPUT LEVEL control to MIN. DOLBY NR and DOLBY HX PRO Dolby NR System To reduce the hiss inherent in tape recording, use the Dolby NR System when making recordings. When listening to a tape recorded with the Dolby NR System, set the DOLBY NR switch to B or C according to the system selected in the recording mode. Note: The sound quality will change if the positions of the DOLBY NR switch are different in recording and playback. Dolby HX PRO headroom extension When a source which contains many high-frequency components is recorded, these high-frequency signals have the same function as bias and therefore, the effective bias current changes. This will result in phenomena such as changes in the level of low-frequency signal and subsequent distortion and reduction of the high-frequency saturation level. Dolby HX PRO headroom extension system controls the bias current so that the effective bias is constant even when there are fluctuations in the high-frequency components of the input signal. This greatly improves the high-frequency saturation level while reducing the low-frequency signal level variations and distortion. • The dynamic sound recorded with this system sounds the same even when the tape is played back in a deck that does not have Dolby HX PRO. • This system automatically works when in recording; however, Dolby HX PRO is not a noise reduction system. COMPU LINK CONTROL SYSTEM The Compu Link Control System controls relative operations between components automatically and facilitates various operations. This is a system originated and developed by JVC for facilitating various system operations. There are two versions of this system; version 1 and 3. (For version 1 components, “COMPU LINK-1/SYNCHRO” is marked on the rear panel. For version 3 components, “COMPU LINK-3/SYNCHRO” is marked on the rear panel. This unit belongs to version 3.) The version 3 system controls relative functions between this unit and an amplifier or receiver, in addition to all of the functions of version 1. Automatic Power On/STANBY Function (COMPU LINK-3) This function is available when an amplifier or receiver having a COMPU LINK-3/SYNCHRO terminal is connected. For example, if a deck contains a tape, the deck is turned on automatically and the tape is played back by only pressing the PLAY button. When the amplifier or receiver is switched STANDBY, the source unit is automatically switched STANDBY. -7- Automatic Source Selection (COMPU LINK-1, 3) When the provided remote cables are used for connecting this unit to other components which have COMPU LINK-1 or 3/SYNCHRO terminals, the switch-over of all system components is possible with simple one-touch of the source selector button of JVC’s amplifier or receiver. By doing this, the corresponding component will start playing automatically. The source select button of the remote control unit or the activation button of the desired component can be also used for this purpose. When the components have been switched over, the previous component will stop playing within five seconds. Synchronized Recording (COMPU LINK-1, 3) Synchronized recording refers to the process in which the deck starts recording in synchronism with the CD player. Perform the synchronized recording as follows: 1. Set the cassette deck to the record-pause mode in accordance with the recording procedures on page 6. 2. If you want the programmed recording, program the desired tunes in any order you wish to hear. 3. Press the PLAY/PAUSE button of the CD player. By so doing, the cassette deck is placed in the record mode and synchronized with the CD player for recording. Synchronized recording thus can be made possible. DDRP (Dynamics Detection Recording Processor) recording The...
Este manual também é adequado para os modelos :Receptores - TD-W271 (1.54 mb)