Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
2. Remove carriage bolts, taking care to support handlebar. 3. Set handlebar to desired height. 4. Line up holes in upper handlebar with holes in lower handlebar. Be sure to use the same holes on each side. 5. Reinstall carriage bolts and wing knobs. Tighten securely. OX0080 GB - 12 CUTTING HEIGHT ADJUSTMENT CUTTING HEIGHT ADJUSTMENT NOTE: There must always be at least one spacer between the cutter disk and the height guide. 1. Hex Shaft 2. Spacers 3. Cutter Disk 4. Height Guide 5. Washer 6. Lock Washer 7. Cap Screw 2 5 1 3 4 6 7 1 spacer = 1-3/16" (3 cm) 2 spacers = 2-3/4" (7 cm) 3 spacers = 3-5/8" (9.2 cm) 4 spacers = 4-3/8" (11.1 cm) OX0090 2 1. Raise the cutter head off the ground. 2. Loosen and remove capscrew, lock washer and washer. 3. Remove height guide and bottom spacer. 4. Remove cutter disk and any of the remaining spacers required to achieve the desired cutting height. 5. Reinstall the cutter disk. 6. Reinstall the spacers required to achieve the desired cutting height. 7. Reinstall height guide on the hex shaft. NOTE: Be sure the hex shaft and the hex hole in the height guide are correctly aligned. 8. Reinstall washer, lock washer and capscrew. Tighten securely. NOTE: The minimum cutting height may be lowered to 1-3/16" (3 cm) by using one spacer below the cutter disk and installing the cutter disk upside down on the hex shaft. HEIGHT GUIDE REPLACEMENT The height guide requires periodic replacement. When used on hard surfaces, such as concrete, it may need to be replaced more frequently. If height guide is damaged or worn, it must be replaced. 1. Raise the cutter head off the ground. 2. Loosen and remove capscrew, lock washer and washer. 3. Remove worn height guide. 4. Install new height guide. 5. Reinstall hardware and tighten securely. SWIVEL HEAD ADJUSTMENT 1. Stop the engine and wait for all moving parts to stop. Disconnect the spark plug wire and place it securely away from the spark plug. 2. Loosen the wing knob on the bracket at the rear of the unit. Wing Knob OX0070 3. Rotate the back of the unit in the opposite direction of the side you wish to cut with. 4. Tighten wing knob securely. GB - 13 GB - 14 CONTROL BAIL TRAVEL ADJUSTMENT Control Bail must disengage trimmer head as control is released. There should be a slight amount of slack in the control cable wire when bail is fully released. If the trimmer head does not disengage completely when the control bail is released, increase the amount of slack in the control cable wire as follows: 1. Loosen the bottom cable nut. 2. Push the cable conduit upward toward the control bail. 3. Tighten the upper cable nut onto the mounting bracket to lock the conduit in place. 4. Turn nuts against mount to lock in position. DRIVE BELT REPLACEMENT 1. Control Cable 2. Control Cable Wire 3. Control Bail 4. Handlebar 5. Cable Nuts 6. Cable Conduit 2 4 5 1 OX0120 3 6 1. Six hex washer head screws 2. Trimmer shield 3. Four hex washer head screws 4. Trimmer frame 5. Jackshaft assembly 6. Jackshaft spacers 7. Jackshaft pulley belt fingers 8. V-belt 9. Jackshaft pulley 10.Engine sheave 11.Capscrew 12.Lock washer 13.Engine sheave belt fingers OX0020 1 2 3 7 8 9 4 5 6 10 11 12 13 1 1 To remove the old belt: 1. Stop the engine and wait for all moving parts to stop. Disconnect the spark plug wire and place it securely away from the spark plug. 2. Place unit in service position (see Maintenance section). 3. Remove the six (6) hex washer head screws and the trimmer shield. 4. Remove the four (4) hex washer head screws on the top side of the frame. The jackshaft assembly, belt fingers and jackshaft spacers will now be loose. 5. Remove the v-belt from the jackshaft pulley. 6. Remove the capscrew and lock washer from the engine sheave. 7. Lower the engine sheave past the belt fingers and remove the belt. To install the new belt: 4 3 2 1 7 6 5 1. Engine sheave belt fingers 2. Engine sheave 3. Idler 4. Idler belt finger 5. V-belt 6. Jackshaft pulley belt fingers 7. Jackshaft pulley OX0100 To remove the old belt: 1. Stop the engine and wait for all moving parts to stop. Disconnect the spark plug wire and place it securely away from the spark plug. 2. Place unit in service position (see Maintenance section). 3. Remove the six (6) hex washer head screws and the trimmer shield. 4. Remove the four (4) hex washer head screws on the top side of the frame. The jackshaft assembly, belt fingers and jackshaft spacers will now be loose. 5. Remove the v-belt from the jackshaft pulley. 6. Remove the capscrew and lock washer from the engine sheave. 7. Lower the engine sheave past the belt fingers and remove the belt. To install the new belt: 4 3 2 1 7 6 5 1. Engine sheave belt fingers 2. Engine sheave 3. Idler 4. Idler belt finger 5. V-belt 6. Jackshaft pulley belt fingers 7. Jackshaft pulley OX0100 1. Slide the new belt over the groove in the engine sheave and slide the sheave against the engine. Make sure the belt is in the groove and is inside the belt fingers. 2. Install the capsc...
Este manual também é adequado para os modelos :Clippers - 946101-ST622 (556.44 kb)
Clippers - 946101-ST622 (556.44 kb)
Clippers - 946101-ST622 (556.44 kb)
Clippers - 946101-ST622 (556.44 kb)