Log:
Assessments - 5, GPA: 4.2 ( )

Instruções de Operação Jonsered, Modelo GT 2125

Fabricante : Jonsered
Arquivo Tamanho: 1.33 mb
Arquivo Nome : JOUS2005_1088931-95.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times. ! WARNING! Never use a machine with faulty safety equipment. The machine’s safety equipment must be checked and maintained as described in this section. If your machine fails any of these checks contact your service agent to get it repaired. English – 7 SAFETY INSTRUCTIONS Cutting equipment IMPORTANT! This section describes how to choose and maintain your cutting equipment in order to: Reduce the risk of blade thrust. Obtain maximum cutting performance. Extend the life of cutting equipment. Only use cutting attachments with the guards we recommend! See the chapter on Technical data. Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter. Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to the instructions on the blade packaging. ! WARNING! Using an incorrect cutting attachment or an incorrectly sharpened blade increases the risk of kickback. Sharpening grass cutters and grass blades • See the cutting attachment packaging for correct sharpening instructions. • Sharpen blades and cutters using a single-cut flat file. • Sharpen all edges equally to maintain the balance of the blade. Trimmer head • Only use the recommended trimmer heads and trimmer cords.These have been tested by the manufacturer to suit a particular engine size.This is especially important when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on Technical data. • Smaller machines generally require small trimmer heads and vice versa. This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared. • The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter. • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.This will make the line tougher so that it lasts longer. IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. ! WARNING! Always stop the engine before doing any work on the cutting attachment. This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it. 8 – English SAFETY INSTRUCTIONS General safety precautions IMPORTANT! The machine is only designed for trimming grass, grass clearing and/or forestry clearing. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination. Never use the machine in extreme weather conditions such as severe cold, very hot and/or humid climates. Wear personal protective equipment. See instructions under the heading Personal protective equipment. Never use a machine that has been modified in any way from its original specification. Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading Maintenance. All covers and guards must be fitted before starting. Make sure the spark plug cap and HT lead are not damaged. Otherwise you could get an electric shock. The machine operator must ensure that no people or animals come closer than 15 metres while working. When several operators are working in the same area the safety distance should be at least twice the tree height and no less than 15 metres. ! WARNING! Using an incorrect cutting attachment or an incorrectly filed blade can increase the risk of accidents. Starting • Place the machine on the ground, ensure the cutting attachment is clear of twigs and stones. Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot). Then grip the starter handle with your right hand and pull the starter cord. Fuel safety • Always use a fuel container with an anti-spill valve. • Never refuel the machine while the engine is running. Always stop the engine and let it cool for a few minutes before refuelling. • Always ensure there is adequate ventilation when handling fuel. • Move the machine at least 3 m from the refuelling point before starting it. • Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or you...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias