Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
2. Push into location and turn safety guard in the direction illustrated in Fig B2, until a click is heard and the safety guard is securely locked in position. • ENSURE THE SAFETY GUARD IS SECURELY IN PLACE BY ATTEMPTING TO TWIST GUARD. Steady Handle Assembly (C) 1. Depress the two buttons on the sides of the switch handle. 2. Locate the steady handle over the buttons and release the buttons. 3. Adjust the steady handle to the most comfortable operating position by depressing the buttons and moving the handle. Height Adjustment (D) 1. Turn height adjuster (D1) in the direction indicated to un-lock (D2). 2. Adjust the length of the tube to the most comfortable operating position. 3. Turn height adjuster in the opposite direction to lock (D3). • ENSURE THAT THE TUBE IS FULLY SECURED. Cable Restraint (E1) & (E2) (optional) 1. Form loop in mains cable and push the loop through the slot as illustrated in picture (E1). 2. To secure, position loop over the hook and pull the cable back through the slot as illustrated in picture (E2). 3 Assembly Instructions cont’ B1 B2 C Double Auto Feed System How the automatic line feed works (F) 1. When initially switching on the trimmer, a small length of line is fed out. 2. A .clattering. noise will be heard when the two nylon lines hit the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. • Make sure the motor is up to full speed before trimming or edging. 3. If the noise of the nylon line being cut cannot be heard, more line will need to be fed out. 4. To feed more line, it is first necessary to to allow the motor to stop completely, then re-start, allowing the motor to reach full speed. 5. Repeat step 4. until you hear the lines hitting against the cutter. (Do not repeat this procedure more than 6 times) 6. If problems are experienced with the automatic line feed refer to Fault Finding Chart. F line cutter E1 E2 D 1 3 2 1 2 CLICK! • WARNING • The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. DISCONNECT FROM THE MAINS ELECTRICITY SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE OR ADJUSTMENT. • BEFORE USE • Make sure that both lines are fed out. • Make sure motor is up to full speed before trimming or edging. How to trim 1. Hold as illustrated in Fig G. 2. To start, squeeze the switch lever. 3. Cut with nylon line at an angle using the tip. See Fig H1. 4. Swing trimmer in and out of the cutting area taking small cuts (H2) 5. Line is fed out automatically every time the trimmer head stops rotating and returns to operating speed. • Extra line can be fed out manually as described in Manual line feed 6. To stop your trimmer release the switch lever. Using the Plant & Tree Guard The Plant and Tree Guard (K1) allows the trimming of grass close to plants and trees without damaging them with the cutting line. 1. Flip the guard down as illustrated in Fig J1. 2. Use the trimmer around trees (J2) and near plants. How to edge 1. To convert to edging mode, press button (K1) and twist head (K2). An audible "click" will confirm that the head is locked. Ensure the Plant and Tree Guard is flipped upwards (K3) 2. Ensure the product is in the correct position for edging as illustrated in Fig L 3. Hold as illustrated in Fig H. 4. To start, squeeze the switch lever. 5. Rest edger on wheel for extra stability and line up the edge of the lawn with the two indicators on the guard (M1). Edge in direction indicated in Fig M. 6. To stop your trimmer release the switch lever. 7. To return to trimming mode, press button and twist head back the opposite way. An audible "click" will confirm that the head is locked. Using the Shrubbing position 1. By pressing the lever (N1) with your foot, the handle can be lowered into three different positions to enable the use of the product under shrubs and low obstacles (P). H1 K G H2 How to use 1 2 1 M J1 J2 3 CLICK! L N P 1 Using the Shrubbing position 1. By pressing the lever (N1) with your foot, the handle can be lowered into three different positions to enable the use of the product under shrubs and low obstacles (P). To manually feed the nylon line (Q) 1. If required line can be fed out manually. 2. To operate, press and release manual line feed button, whilst gently pulling on one of the lines until the line reaches the line cutter. 3. When the required amount of line is fed out, gently pull on the second line (there is no need to press the manual line feed button again). 4. If the line extends past the line cutter, too much line has been fed out. 5. If too much line is fed out, remove the spool cap and click spool anti-clockwise until the line is at the desired length. • Always return t...