Assessments - 2, GPA: 4
(
)
)
|
Fotos e especificações Flymo Sabre Trim |
Facilidade de uso
To fit spool and line complete: 1. Remove old spool. 2. Place new spool into spoolholder with cut out area of the spool in line with eyelet as shown in figure V. 3. Release line from cleat and feed line through eyelet (V). • Ensure spool is fully located by gently rotating it dur- ing fitment, whilst keeping the spoolholder steady. 4. Refit the cap. To fit nylon line only: • Remember! Your product is designed to use only nylon line with a maximum diameter of 1.5mm. Use only genuine Flymo nylon line. 1. Take approximately 10 metres of line. Insert 15mm of line into the hole in the spool (W) and wind line in the direction of the arrows on the top of the spool. Leave approximately 100mm of line unwound and place into cleat as illustrated in figure W1. 2. Care should be taken to ensure that the line is neatly coiled on the spool. Failure to do so will impair the efficiency of the automatic line feed. 3. Then fit spool as described in ‘To fit spool and line complete’, section above. Cap Cap release latchSpool Spoolholder Eyelet T V W Cleat Cut out area of spool Eyelet W1 Manual line feed S manual line feed button To manually feed the nylon line (S) 1. If required line can be fed out manually. 2. To operate, press and release manual line feed button, whilst gently pulling on the line until it reaches the line cutter. 3. If the line extends past the line cutter, too much line has been fed out. 4. If too much line is fed out, remove the spool cap and click spool anti-clockwise until the line is at the desired length. Cap Cap release latchSpool Spoolholder Eyelet T V W Cleat Cut out area of spool Eyelet W1 Manual line feed S manual line feed button To manually feed the nylon line (S) 1. If required line can be fed out manually. 2. To operate, press and release manual line feed button, whilst gently pulling on the line until it reaches the line cutter. 3. If the line extends past the line cutter, too much line has been fed out. 4. If too much line is fed out, remove the spool cap and click spool anti-clockwise until the line is at the desired length. Maintenance • WARNING X1 X2 Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your product After you have finished using your product follow the procedure below: 1. Never clean your trimmer with water, cleaning fluids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth. 2. Using a soft brush, clean around the inside of the safety guard, the cutting head (X1) and the motor housing air vents. (X2) 3. Remove the wheel by pressing one of the buttons. Clean the wheel and groove on trimmer head with a soft brush (X3 & X4). 4. Attach wheel as described in Wheel Assembly. 5. Inspect the product carefully, especially the parts of the cutting head. 6. If your product is damaged in any way contact your local Husqvarna Outdoor Products approved service centre. • Never use a damaged product. Storing your product 1. Attach the Steady Handle Storage Holder to the wall with the two screws provided (Y1) 2. Store the Steady Handle in the holder as illustrated in Fig Y2 3. Attach the Trimmer Head Storage Holder to the wall with the two screws provided (Z1) 4. Store the Trimmer Head in the holder as illustrated in Fig Z2 • Store in a cool, dry place and out of reach of children. X4 X3 Y1 Z1 Y2 Z2 Fault Finding Chart FAULT CHECK ACTION Is the automatic line feed working? Manually feed out line. SEE “MANUAL LINE FEED” Is the line fed out and visible? Has line been removed from cleat? Remove cap and spool, free line and re-fit spool and cap. SEE “CUTTING HEAD” The line may be jammed on the spool. Rewind line to remove crossed loops. Check that line is in correct section of spool. Is the manual line feed working? Has too much line been fed out? SEE “MANUAL LINE FEED” Contact your local approved Service Centre or Husqvarna Outdoor Products Customer Service. Is the line cutter missing from the safety guard? Contact Husqvarna Outdoor Products Customer Service Telephone : 01325 302302 No No No Yes Yes LINE NOT FEEDING OR LINE TOO SHORT OR TRIMMER VIBRATES CONTINUOUS CLATTER- ING NOISE LINE SNAPS CONTINU- OUSLY IF NONE OF THE ABOVE OR IF FAULT PERSISTS Has the motor reached full speed before use? No Allow the motor to reach full speed before use. Are you using the trimmer correctly? ? Only use tip of nylon line to trim. SEE “How to trim and edge” Is the line jamming on the spool? Yes Rewind the line on the spool, if symptoms still persist, change spool and line. Clean wheel and groove on trimmer head. SEE “MAINTENANCE” WHEEL STOPS TURNING Environmental Information Husqvarna Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life. • Packag...