Assessments - 4, GPA: 3.3
(
)
)
|
Fotos e especificações Flymo POWER TRIM 600 HD |
Facilidade de uso
2. To secure, position loop over the hook and pull the cable back through the slot as illustrated in picture (E2). 3 Assembly Instructions B1 B2 A1 Double Auto Feed System How the automatic line feed works (F) 1. When initially switching on the trimmer, a small length of line is fed out. 2. A .clattering. noise will be heard when the two nylon lines hit the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. • Make sure the motor is up to speed before trimming or edging. 3. If the noise of the nylon line being cut cannot be heard, more line will need to be fed out. 4. To feed more line, it is first necessary to to allow the motor to stop completely, then re-start, allowing the motor to reach full speed. 5. Repeat step 4. until you hear the lines hitting against the cutter. (Do not repeat this procedure more than 6 times) 6. If problems are experienced with the automatic line feed refer to Fault Finding Chart. F line cutter A2 E1 E2 CLICK! CLICK! C D 1 3 2 1 2 • WARNING • The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. DISCONNECT FROM THE MAINS ELECTRICITY SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE OR ADJUSTMENT. • BEFORE USE Make sure that both lines are fed out. Make sure motor is up to speed before trimming or edging. How to trim • YOUR PRODUCT CONTAINS ELECTRONIC SPEED CONTROL FOR YOUR SAFETY. YOUR PRODUCT WILL START SLOWLY AND SPEED UP WHEN YOU START CUTTING. 1. Hold as illustrated in Fig G. 2. To start, squeeze the switch lever. 3. Cut with nylon line at an angle using the tip. See Fig H. 4. Swing trimmer in and out of the cutting area taking small cuts (J) 5. Line is fed out automatically every time the trimmer head stops rotating and returns to operating speed. • Extra line can be fed out manually as described in Manual line feed 6. To stop your trimmer release the switch lever. How to edge 1. To convert to edging mode, depress the locking button (K1) and twist head anti-clockwise (K2). An audible "click" will confirm that the head is locked. Ensure the button has returned to its original position. 2. Hold as illustrated in Fig G. 3. To start, squeeze the switch lever. 4. Rest the edger on the roller for extra stability and line up the edge of the lawn with the two indicators on the guard (L1). Edge in direction indicated in Fig L. 5. To return to trimming mode, depress the locking button and twist head clockwise. An audible "click" will confirm that the head is locked. Ensure the button has returned to its original position. H K J How to trim and edge 1 2 1 L G To manually feed the nylon line (M) 1. If required line can be fed out manually. 2. To operate, press and release manual line feed button, whilst gently pulling on one of the lines until the line reaches the line cutter. 3. When the required amount of line is fed out, gently pull on the second line (there is no need to press the manual line feed button again). 4. If the line extends past the line cutter, too much line has been fed out. 5. If too much line is fed out, remove the spool cap and click spool anti-clockwise until the line is at the desired length. Manual line feed M manual line feed button Cutting Head To remove spool cap 1. Press and hold in the two cap release latches. (N). 2. Pull cap away from the spoolholder. (N). When refitting the spool cap 1. Keep all areas of the cap and spoolholder clean. Failure to do so may prevent the cap being securely located in the spoolholder. 2. Replace the cap, pressing firmly DOWN towards the spoolholder to ensure cap is fully located. 3. Check that the cap is correctly fitted by trying to remove it without depressing the two latches. To replace nylon line For your convenience it is recommended you buy spool and line complete. Nylon line only is also available. Both are available from Husqvarna UK Ltd. stockists. To fit spool and line complete: 1. Remove the cap. 2. Remove old spool. 3. Place spool into spoolholder. 4. Release one line from cleat (Q1). 5. Secure line into slot (P1). 6. Repeat for second line. • Ensure spool is fully located by gently rotating it during fitment, whilst keeping the spoolholder steady. 7. Refit the cap. To fit nylon line only: • Remember! Your Flymo Trimmer is designed to use only nylon line with a maximum diameter of 2.0mm. Use only genuine Flymo nylon line. 1. IMPORTANT - Always wind the line onto the upper section of the spool first. Take approximately 5 metres of line. Insert 15mm of line into one of the holes in the upper section of the spool (Q) and wind line in the direction of the arrows on the top of the spool. Leave approximately 100mm of line unwound and place into cleat as illu...