Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
To keep good cutting performance, also use a cutting lubricant from time to time during operation. Switch action To start the tool, move the slide switch forward, and the slide switch will lock in the "ON" position. To stop, lightly depress the rear of the slide switch, and it will re- turn to the "OFF" position. CAUTION : Before plugging in the tool, always check to see that the slide switch actuates pro- perly and returns to the "OFF" position when depressed. Operation Turn the tool on and set the front ends of the side blades on the workpiece. Now simply move the tool forward, keeping the side blades flush with the workpiece surface. CAUTION : When cutting a small portion of the work- piece, you may have difficulty complet- ing the end of the cut. In that case, try to cut it again, pulling the workpiece back slightly. Slide switch 7 r- 5 MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both * carbon brushes should be replaced at the same time. Use only Makita carbon brushes. Limit mark Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. Workpiece Thickness Cutting length Mild steel I 1.6 mm (1/16") I 200 m ( 656 ft.) Hard steel 1.2 mm (3/64") 180 m ( 590 ft.) Stainless 1.2 mm (3/64") 150 m ( 492 ft.) Aluminum 2.0 mm (5/64") 400 m (1,312 ft.) To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 6 ACCESSOR IES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Hex wrench 3 0 Wrench holder Part No. 783201-2 Part No. 410048-8 0 Thickness gauge Part No. 762013-6 May-08-'87 EN STRAIGHT SHEAR Model JS1660 Note: The switch, noise suppressor and other part configurations may differ from country to country. MODEL JS1660 July-17-'89 US 'EM ,& DESCRIPTION ';iM ,,& DESCRIPTION MACHINE MACHINE ~ Pan Head Screw M4x35 (With Washer) 30 1 Slip Piate L Block 31 1 SPEC*' Hex. Lock Nut M4-7 32 1 Side Blade Set Screw M5x12 33 1 Hex. Socket Head Bolt M5x10 PI" 7 34 1 Hex. Socket Head Bolt M4x25 Stop Ring E-6 35 1 Hex Socket Head 8olt M5x10 Rubber Pm 4 36 1 Stop Ring E-4 st 1 Ball Bearing 627LLB 37 1 Teflon Washer 7 Flat Washer 7 38 1 Thin Washer 7 Rod 39 1 Center Blade Bail Bearing 60wLLB 40 1 Thin Wisher 7 Crank Shaft 41 1 Teflon Washer 7 Bush 42 1 Flat Washer 5 14 1 1 Ball Bearing 60wLB 43 1 Flat Washer 5 15 1 HeIicai Gear 44 44 1 Switch Rod 16 1 Retaining Ring 5-10 45 1 Compression Spring 6 17 1 Ball Bearing 608L8 46 1 Housing Sat IWith Item 591 18 1 Fan 52 47 1 Cord 19 1 ARMATURE ASSEMBLY 48 1 Card Guard IWith Item 17 -201 49 1 Strain Relief 20 1 Ball Bearing 627LLB 50 2 Pan Head Screw M4x18 (With Washer1 21 1 FIELD ASSEMBLY 51 1 Rubber Pm 4 Woodruff Key 3 52 1 Swnch P," 5 54 1 Rubber Pin 4 24 1 Link 55 2 Carbon Brush 25 1 Pl" 5 56 2 Brush Holder Cap 26 1 Dust Cover 57 1 Name Plate 27 1 Crank Housing 58 5 Pan Head Screw M4x30 IWith Washer1 28 1 Slip Plate R 59 1 HouPing Set IWith Item 461 29 1 Side Blade 1 Note: The switch and other pert specifications may differ from country to country. MAKmALIMEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is wananted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. ThisWarranty does not apply where: repairs have been made or attempted by others: repain are required because of normal wear and tear: The tool has been abused, misused or improperly maintained; alterations have been made to the tool. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CON- SEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF “MERCHANTABILITY’ AND “FITNESS FOR A SPECIFIC PURPOSE, AFTER THE ONE-YEAR TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or ...