Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
5. Do not put the tool on the chips of the workpiece. Otherwise it can cause damage and trouble on the tool. 6. Do not leave the tool running. Operate the tool only when hand-held. 7. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 8. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 9. Avoid cutting electrical wires. Itcan cause serious accident by electric shock. SAVE THESE INSTRUCTIONS. SYMBOLS The followings show the symbols used for tool. v ..................................... olts A .................................... amperes Hz .................................... herts % .................................... alternating current n, .................................... no load speed loi .................................... Class II Construction ..Jmin ................................... revolutions or reciprocation per minute FUNCTIONAL DESCRIPTION Switch action CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released Switch trigger 1 d Hook The hook is convenient for temporary hanging the tool. When using the hook, pull it out in "A" direction and then push it in "B" direction to secure in place. When not using the hook, return it back to its initial position by following the above proce- dures in reverse. ASSEMBLY Replacement of blades CAUTION: *Always be sure that the tool is switched off and unplugged before replacement of the blades. Never remove the blades with bare hands. Wear gloves. Otherwise it can cause injury. Removing cutting head Use the hex wrench to loosen the three t Cutting head screws which secure the cutting head. Pull the cutting head straight out to remove it with turning it left and right alternately. Screws 'Hex wrench Removing shear blades Remove the three screws which hold the cutting head. When removing the second screw, be careful not to fall the sleeve. Then the blades can be removed easily. When removing the blades, hold the blades and the sleeve so that they do not fall from the cutting head. Installing shear blades Install the sleeve and tighten th. three screws after inserting the center blade, side blade L & R into the cutting head. In this process, the screw heads should be protruding 2 -3 mm from the cutting head surface. If you will tighten the screws excessively, the cutting head cannot be installed to the tool. Screws Side blade L Center blade Side blade R Installing cutting head CAUTION: Secure the cutting head firmly. Otherwise it can rotate during operation and can cause serious injury. Insert the cutting head into the tool with turning it left and right alternately. Then tighten the three screws with the hex Cutting head 7 wrench. I I \Hex wrench OPERATION CAUTION: Edges and chips of the workpiece are sharp. Wear gloves. Otherwise it can cause injury. Secure the workpiece firmly. Move the tool forward keeping the side blades flush with the workpiece surface. Adjusting shear blade Adjust the side blade L so that the curl of waste material does not contact the cutting head or the workpiece. Use the hex wrench to loosen the three screws which hold the cutting head. Move the side blade L back and forth to adjust it. Then tighten the three screws with the hex wrench. Center blade I Side blade L -, Screws &Side blak 'Ieeve 1 Center blade MA1 NTE NANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Lubrication Before operation, lubricate the contact point of the center blade and the side Side blade L -I Lubricate blades R/L. And, also lubricate the point of the center blade near the cutting head. To keep good cutting performance, also use lubricant from time to time during opera- tion. Side blade R I Center blade To maintain product SAFETY and reliability, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita placement parts. ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Side blade R Center blade Hex wrench Side blade L 10 ITEM NO. DESCRIPTION NO USED 1 2 3 4 6 1 8 11 12 13 14 16 11 18 19 22 23 24 26 21 28 29 31 32 33 34 36 31 38 39 41 42 43 44 46 41 48 CENTERBLADE 1 SIDE BLADE R 1 SLEEVE 5 1 SIDE BLADE L 1 CUTTING HEAD COMPLETE 1 HEX. SOCKET HEAD BOLT 3 GEAR HOUSING 1 TAPPING SCREW 4x30 3 BEARING ASS'Y 1 BEARING RETAINER 19-33 1 FLAT WASHER 10 1 SPINDLE 1 BALL BEARING 6201DDW 1 BALL BEARING 606 1 GEAR COMPLETE 17-35 1 FLAT WASHER 8 1 RING 12 1 SPUR GEAR 36 1 FAN 52 1 GEAR HOUSING COVER COMPLETE 1 BALL BEARING 608VV 1 ARMATURE ASS'Y 1 INC. 2023.25.26...