Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
It can be replaced. Knob Cutter bar Latch (opens top cover) Feed Deck. The LX-570 is designed for use with items up to five inches wide. It works best with item thicknesses between 20 pound bond paper and 100 pound card stock or construction paper (min. thickness is 0.004 inches, max. thickness is 0.010 inches). The LX-570 applies an adhesive, laminate, or magnetic backing to an item without using heat or electricity. You choose a backing by swapping the drop-in cartridge. The LX-570 comes with a starter cartridge already installed. This cartridge applies a permanent adhesive backing and is shorter than replacement cartridges. See the reverse for available cartridges and for application ideas on using your LX-570. First, take a few minutes to read these instructions. Top Cover. Your LX-570 comes with a "starter" cartridge already installed, which applies a permanent adhesive backing to an item. Cut: When the item clears the cutter at the exit area, gently push down on the cutter knob and slide it all the way to the left or right. Insert the item: Insert the item face up at the feed deck and turn the knob in the direction of the arrows only; do not turn knob backwards. To avoid wasting the backing material, note the location of the cut. Feed only enough material to clear the cutter. How to Use the LX-570 Insert the item and be sure it is straight. Insert until you feel contact; then release it as you turn knob. Exit area When Using the Starter Cartridge... Feed and cut the item as described here. Be sure to feed face up. Press down firmly around all the edges. This action prevents adhesive from remaining on the front of the item. Then remove the clear film and discard carefully as it is sticky. When you are ready to place the item on a surface, peel it from the white backing. This starter cartridge contains five feet of backing material. After you use it a few times, always make certain that it contains sufficient material. If uncertain, install a new cartridge to avoid partial processing. Note: the starter cartridge is shorter than the replacement cartridges. See the other side for cartridge descriptions and lengths. Always consult packaging of replacement cartridges. User’s Guide 1 2 LX-570 About the LX-570 Feed straight, not at an angle. Turn the knob forward only. Notes: Before using, remove the protective tape and other packaging materials under the top cover. Under the terms of an agreement with Xyron, Inc., the purchase or other acquisition of this product confers no right or license to use the product in the Retroreflective Field. How to Change the Cartridge Remove the cartridge: Lift up the latch to open the top cover. Then grasp the cartridge in one hand, hold the LX-570 with the other, and lift the cartridge up and out. Insert a cartridge: Open the top cover and lower the cartridge in with the label up, facing the feed deck. As you lower the cartridge, be sure that the backing material fits underneath the cutter bar at the exit area. Close the top cover by gently pushing down until it clicks and is fully seated. 1 Unsnap the cutter: Place your thumb underneath the back of the cutter knob and your index finger on the cutter bar. Lift up with your thumb to unsnap the cutter from the cutter bar. How to Change the Cutter Blade is at this end and fits into a groove on the cutter bar. Always avoid touching the blade. Snap the new cutter into place: At any point on the cutter bar, place the front of the cutter into the groove on the cutter bar so the blade fits into it. Then rotate the cutter back and snap down. Blade is at front of cutter. Avoid touching the blade. Back of cutter Front of cutter Guide the backing material under the cutter bar into the exit area. Notes: When placing a partially-used cartridge back in the machine, be sure the material does not adhere to the cartridge itself. When removing a used cartridge whose material has wrapped around the rollers, remove the cartridge and pull the material from the rollers. Groove in cutter bar 1 1 2 2 When installed properly, the cutter slides back and forth on the cutter bar. The cartridge is properly installed when the label is flush with the feed deck. Close the top cover before using. US5022001 Never place your finger under the cutter bar at the cutter. When handling cutters, take care to avoid injury to yourself or others. Avoid ingestion of the backing material or cutter. Avoid contact of adhesive backing materials with skin or other delicate surfaces. Keep fingers out of the top cover when closing. Warnings & Cautions Warnings: Cautions: All backing materials are permanent once applied and cannot be removed without damage. Do not use on single-source items. Once you start feeding an item, do not try to back it out by turning the knob in the opposite direction. Always feed items straight, not at an angle. Before processing an item, make certain that the cartridge contains sufficient backing material. If uncertain, install a new replacement cart...