Assessments - 3, GPA: 4.7 ( )

Fabricante : Electrolux Arquivo Tamanho: 2.08 mb Arquivo Nome : Língua de Ensino:

Cutting with the nylon string head is suitable for light jobs like trimming borders and cutting the grass around trees. Mowing To prevent damage to your lawn or the cutting mechanism, keep the string parallel to the ground but avoid contact with the terrain. Trimming borders Angle the nylon string head keeping it a short distance from the ground. Cut using the end of the string. Do not press the string against the material to be cut. Drawing out the string As you cut, the nylon string wears down naturally (see paragraph entitled “String head”). Thinning grass with the grass cutter blade . CAUTION! Always work with a sharp blade. A blade with worn teeth can create problems in cutting and can cause KICKBACK, that is, a violent thrust on the front of the machine caused by the impact of the blade against wood or solid foreign bodies. This kickback can cause loss of control of the machine. Never sharpen a damaged blade: replace with a new one. . N1. CAUTION! Do not let the blade cut in the risk sector to prevent kickback (see paragraph “Safety precautions”). Cutting with the blade is recommended for thinning the The machine is ideal to complete the work of the grass, especially when tall and sturdy. lawnmover. In fact, it can reach places where a normal N2. The grass is cut with swinging motions from side to lawnmower is unable to go. side, maintaining the blade parallel to the ground. During During the cutting operations, keep the engine running at the right to left swing the grass is cut, while the backswing high speed. After every cutting stage, decelerate the ENGLISH -9 must be made without using the blade. KICKBACK can occur when cutting is done with the risk sector of the blade; we recommend cutting with the rest of the blade. Take care that the cup supporting the blade just grazes the ground. This will prevent the blade from touching the ground. . N1. CAUTION! WE RECOMMEND THE USE OF ORIGINAL ACCESSORIES AND REPLACEMENTS; THESE CAN BE FOUND AT YOUR OFFICIAL DISTRIBUTOR'S. THE USE OF ACCESSORIES AND REPLACEMENTS THAT ARE NOT ORIGINAL INCREASES THE DANGER OF ACCIDENTS AND IN THIS CASE THE MANUFACTURER IS NOT LIABLE FOR ANY DAMAGES TO PERSONS OR PROPERTY. O. Environmental information This section contains information useful for maintaining the characteristics of eco-compatibility included in the origin design of the machine, and as regards proper use and disposal of oil and fuel. Design In the design stage, care was taken to develop an engine with reduced consumption and low emissions of noise and pollutant exhaust fumes. Use of machine The operations of filling the tank with the fuel mixture should be carried out in such a way as to avoid spilling fuel and contaminating the soil and environment. Periods of prolonged disuse Always empty the fuel tank with the same precautions used in filling it (O). Disposal Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized organization for proper disposal in compliance with the regulations in force. P. Troubleshooting table The engine does not start The engine stutters or loses power The machine starts but does not cut properly Make sure the STOP switch is on I. . Make sure that the fuel tank is at least 25% full. . . Make sure the air filter is clean. . . Remove the sparkplug, dry and clean it, then return it to its place. If necessary, replace it. . . Change the fuel filter. Contact your supplier. . Follow the correct procedure for assembly of the cutting accessories. . Make sure the metal accessories are sharp, and contact your supplier if necessary. . The engine continues to have problems: contact your authorized supplier 10 -ENGLISH Q. Declaration of conformity The undersigned, authorized by E.O.P., declares that the following products model: type BC022, BC010C starting from the serial numbers produced from 2001 on, manufactured by E.O.P., Valmadrera, Italy, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) & 89/336/EEC (Electromagnetic Compatibility Directive), directive 2000/14/EEC (Enclosure V). Valmadrera, 15/12/01 Giuseppe Todero (Technical Manager) Electrolux Outdoor Products Italy S.p.A....

Baixe o seu

Para fazer o download, introduza 2 dígitos :