Assessments - 2, GPA: 4
(
)
)
|
Fotos e especificações Scarlett SC-1262 |
Facilidade de uso
Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual. Do not use outdoors. Always unplug the appliance from the power supply before cleaning and when not in use. To prevent risk of electric shock and fire, do not immerse the appliance in water or in any other liquids. If it was happened DO NOT TOUCH the appliance, unplug it immediately and check in service center. Do not take this product into a bathroom or use near water. Close supervision is necessary when it is used near children. Do not leave the appliance switched on when not in use. Do not use other attachments than those supplied. Do not operate after malfunction or cord damage. Do not attempt to repair, adjust or replace parts in the appliance. Check and repair the malfunctioning appliance in the nearest service center only. Keep the cord away from sharp edges and hot surfaces. Do not pull, twist, or wrap the power cord around appliance. Never drop or insert any object into any opening on this appliance. Before use, make sure that blades are adjusted properly. 3 SC-1262 • Do not put operating appliance on any surface, it may cause injury or damage. • Do not use this appliance with a damaged comb, or with teeth missing from the blades as injury may occur. NOTE: KEEP BLADES OILED. • Do not use the hair clipper when the skin is infected. • Do not use the hair clipper on animals. BLADE ALIGNMENT • Your clipper was carefully examined to ensure that the blades were oiled and properly aligned before leaving our factory. • Blades must be realigned if they were removed for cleaning or after replacement. • To realign the blades, simply match the upper and lower blades teeth up, point for point. • End of top blade teeth should be approximately 1.2 mm back from lower blade. Compare your clipper blades with the sketch (pic.1). • If blade alignment is incorrect, add a few drops of oil to the blades, switch on clipper for a few moments, switch off and unplug. Loosen screws slightly and adjust. Tighten screws after blade is aligned. OILING • To maintain your clipper in peak condition, the blades should be oiled after every haircut. • Do not use hair oil, grease, oil mixed with kerosene or any solvent. BLADE LEVER • The lever, located at the left of the blades, allows easily adjust cut hair length while keeping the clipper. • The lever adds versatility to your clipper by allowing you gradually change the closeness of your cut without an attachment comb. • When the lever is in the uppermost position, the blades will give you the closest cut and leave the hair very short. Pushing the lever downward gradually increases the cutting length. • In its lowest position, the lever will leave the hair approximately the same length as a №1 (3mm) comb. • The lever will also extend the use of your blades since a different cutting edge is used in each setting. • In addition, if extremely heavy hair cutting has jammed the blades, it will help you remove hair that has become wedged between the two blades without removing the blades. • While the clipper is running rapidly move the lever from “close cut” to “longer cut” a couple of times. Doing this each time after you have finished using your clipper to keep the blades free of cut hair. • If this does not help and clipper stops cutting, blades are dulled. Replace them with new blades. INSTRUCTIONS FOR HAIR CUTTING • Before starting the hair cut inspect the clipper, making sure that there is no oil between the cutting blade teeth, switch the unit on to distribute the oil and to check running smoothness. Wipe off any excess oil. This should be done after each use. While using the unit, untwist the cord from time to time to avoid tangling. • Before cutting always first comb the hair thoroughly. DETACHABLE COMBS Attachment comb № - Hair length mm (inches) №1 - 3 (1/8) №2 - 6 (1/4) №3 - 9 (3/8) №4 -12 (1/2) • Each comb attachment is marked accordingly on its outside middle surface. • To attach a comb, hold it with its teeth upward and slide onto and along the clipper blade until the front of the comb firmly seats against the clipper blade. • When you use the clipper for the first time, cut only small portions of hair. • For even cutting do not force clipper. Also remember to comb the hair more frequently to remove trimmed hair and check for uneven strands. CARE AND CLEANING • Switch off the appliance and unplug it. • Clean and oil the appliance after each use. • Remove cut hair from the clipper with the brush enclosed. • Wipe the cutter with a dry soft cloth. • Oil the blades as mentioned above. STORAGE • Keep the appliance in a dry room. • You may hang the cutter by provided loop. • The blades must be oiled for storage period. РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ МЕРЫ БЕЗОПАСНОСТИ • Внимательно прочитайте Руководство по эксплуатации и сохраните его в качестве справочного материала. • Пере...