Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
(2.0 mm) UNPACKING INSTRUCTIONS ¦ ¦¦¦¦¦Carefully remove the product from the carton. ¦ ¦¦¦¦¦Inspect the product to make sure no breakage or damage occurred during shipping. ¦ ¦¦¦¦¦Do not discard the packing material until you have inspected and operated the product. ¦ ¦¦¦¦¦If any parts are damaged or missing, please call 1-800-chainsaw (1-800-242-4672) for assistance. PACKING LIST ¦ ¦¦¦¦¦Trimmer Assembly ¦ ¦¦¦¦¦Owner’s Kit ¦ ¦¦¦¦¦Front handle ¦ ¦¦¦¦¦Grass deflector ¦ ¦¦¦¦¦Edger Guide for Trim ‘n Edge only ¦ ¦¦¦¦¦Hardware Bags (2) ¦ ¦¦¦¦¦Bottle of 2-Cycle Oil ¦ ¦¦¦¦¦Operator's manual FEATURES OP Fig. 1a THROTTLE TRIGGER STARTER GRIP CHOKE LEVER REAR HANDLE FRONT HANDLE DRIVE SHAFT HOUSING STRING HEAD GRASS DEFLECTOR STOP BUTTON PRIMER BULB Trimlite model UT20930 Page 5 Page 6 STSTOPOP 1 2 3 STOPOP 1 2 3 FEATURES Fig. 1b Fig. 1c EDGER ATTACHMENT (TRIM ‘N EDGE ONLY) THROTTLE TRIGGER STARTER GRIP CHOKE LEVER REAR HANDLE FRONT HANDLE DRIVE SHAFT HOUSING STRING HEAD GRASS DEFLECTOR STOP BUTTON PRIMER BULB THROTTLE TRIGGER STARTER GRIP CHOKE LEVER REAR HANDLE FRONT HANDLE DRIVE SHAFT HOUSING STRING HEAD GRASS DEFLECTOR STOP BUTTON PRIMER BULB Trim ‘n Edge model UT20933 Easy Reach models UT20777 ASSEMBLY If your unit has been preassembled, check each step to make sure the unit has been properly assembled. FRONT HANDLE See Figure 2. 1. Remove the front handle, bolt, and wing nut from the Owner’s Kit. 2. Install the front handle onto the top side of the drive shaft housing and move it to a comfortable position. 3. Place the bolt through the front handle as shown, then install the wing nut. 4. Tighten wing nut securely. GRASS DEFLECTOR WITHOUT EDGER GUIDE - TRIMLITE AND TRIM ‘N EDGE See Figure 3. 1. Remove wing nut, flat washer, lock washer, and bolt from the Owner’s Kit. 2. Place grass deflector over shaft and bracket. 3. Install bolt through the slots in the tabs on grass deflector and bracket on shaft housing. 4. Install flat washer, lock washer and wing nut. 5. Tighten Securely. GRASS DEFLECTOR WITH EDGER GUIDE TRIM ‘N EDGE ONLY EDGER GUIDE ASSEMBLY See Figure 4. 1. Assemble the two plastic pieces of the edger guide together using the short bolt, flat washer, lock washer and wing nut. 2. Slide the edger guide to adjust it to the desired trimming length. 3. Tighten the wing nut securely. GRASS DEFLECTOR BRACKET BOLT WING NUT Fig. 3 WING NUT FRONT HANDLE BOLT Fig. 2 FLAT WASHER LOCK WASHER EDGER GUIDE PIECES SHORT BOLT FLAT WASHER LOCK WASHER WING NUT Fig. 4 Page 7 ASSEMBLY GRASS DEFLECTOR WITH EDGER GUIDE TRIM ‘N EDGE ONLY (Continued) See Figures 5 and 6. 1. Remove the wing nut, flat washer, lock washer, and bolt from the Owner’s Kit. 2. Place the grass deflector over the shaft and bracket. 3. Slide the assembled edger guide over the tabs on the grass deflector and bracket. 4. Place the bolt through the slots in the tabs on the grass deflector and trimmer. NOTE: Ensure the slots are aligned before installing the bolt. 5. Install the flat washer, lock washer and wing nut. 6. Tighten the wing nut securely. GRASS DEFLECTOR - EASY REACH See Figure 7. 1. Remove the wing nut from the Owner's Kit. 2. Place slot in grass deflector over the square tab of the mounting bracket. 3. Rotate the deflector around the drive shaft housing then insert the screw on the grass deflector into the screw hole in the mounting bracket. The mounting surface of the grass deflector should fit flush on the mounting bracket. 4. Install the wing nut and tighten securely. ASSEMBLED EDGER GUIDE TABS FLAT WASHER LOCK WASHER WING NUT LONG BOLT Fig. 6 WING NUT GRASS DEFLECTOR SLOT SCREW SQUARE TAB Fig. 7 Fig. 5 Page 8 OPERATION FUELING AND REFUELING THE TRIMMER FUEL MIXTURE This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean 1 gallon container approved for gasoline. Recommended fuel: This engine is certified to operate on unleaded gasoline intended for automotive use. Mix Homelite Premium Exact Mix oil with gasoline according to the instructions on the package. If Premium Exact Mix oil is not available, use a high quality 2-cycle engine oil, mixed at 2.6 oz. per gallon (US). Do not use automotive oil or 2-cycle outboard oil. NOTE: Premium Exact Mix fuel mix will stay fresh up to 30 days. DO NOT mix quantities larger than usable in a 30 day period. FUEL MIXTURE PREMIUM EXACT MIX (50:1) GASOLINE OIL 1 gallon (US) 2.6 oz. 1 Liter 20 cc (20 ml) FILLING TANK 1. Clean surface around fuel cap to prevent contamination. 2. Loosen fuel cap slowly. Rest the cap on a clean surface. 3. Carefully pour fuel into the tank. Avoid spillage. 4. Prior to replacing the fuel cap, clean and inspect the gasket. 5. Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage. NOTE: It is normal for smoke to be emitted from a new engine after first use. WARNING: Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at ...
Este manual também é adequado para os modelos :Clippers - UT20930 (993.61 kb)